Comments

• 

  Loco October 28, 2011 at 11:18am

  George, any chance of getting a picture of you CBU TwoSPot? would love to see the progress...thats the best part...

   

  Thanks the headstock is coming along well.

   

  Loco
• 

  Loco October 26, 2011 at 2:32pm

  George,

   

  On your question about Fretting....I dont have the right saw so I used what I had in stock which was a metal saw(smaller than your normal wood saw blade). The blade was still too big but not big enough that it would wiggle around in the slot. I then applied glue bond and cleaned off the excess. In the future I will purchase a proper fretting saw but for now this is my way and only way.

  Hope this helps.

  Loco
• 

  Loco October 21, 2011 at 2:37pm

  Thanks George, I was impressed too. I never owned a Uke either.

  Loco
• 

  Yellowbelly Flatt September 27, 2011 at 6:02pm

  Yes George. the scale length has to be the same as the original or the fitted frets on the old neck will not play in tune.

   

  if there are no frets on the old neck then you can use any scale you like. Have you ever tried to play chords on a fretless ukulele?
• 

  Yellowbelly Flatt September 26, 2011 at 5:47pm

  As long as the scale length of the new instrument is the same as the old one, you should be fine.
• 

  Yellowbelly Flatt September 25, 2011 at 5:04am

  The reason I mentioned about measuring the distance between the nut and the bridge was to make the positioning of the bridge on your new instrument much easier. If you are building a fretted instrument the scale length - and so the position of the bridge - is all relative to the positioning of the frets. With a small scale length (the distance between the nut and bridge) such as a ukulele, this positioning can affect the intonation of the fretted notes quite appreciably.

  If the bridge is perhaps 1/4" out, the notes played by the fretting of the strings will not be correct. Ukuleles don't usually have adjustable bridges like you might find on an electric guitar so there is little chance of any adjustment once the bridge is in position, unless you use a bridge and tailpiece like (for example) a banjo..

  There are however several computer applications that would allow you to formulate the correct dimensions. Check out the scale lengths group on the.nation's groups section.

  I hope this answers your question and that I haven't made the question more difficult?
• 

  Yellowbelly Flatt September 24, 2011 at 3:10am

  Good luck with that. Have you measured the nut to bridge length and the angle of the neck to the body?
• 

  Yellowbelly Flatt September 23, 2011 at 5:07pm

  Hi there George,

  thank you very much for adding me as a friend on cigar box nation.

  I see that you would like to use a soprano uke neck with a cigar box. Please make sure that you have a substantial block of wood inside the box where the neck joins the box   .I then screw the neck to the box from the inside, or you can get a special screw that you screw into the neck and then bolts to the box. these are really useful as the neck can be detached from the box. just use a dowel or something in order to keep the neck "SQUARE" to the box.
• 

  Yellowbelly Flatt September 23, 2011 at 1:20am

  For this guitar - and the stand up bass - I used what are known in this country strimmer lines of different thicknesses. I understand that over there they are known as weed whackers or bush cutters. These are nylon lines that are used on machines for cutting down long grass and scrub type plants. Initially they stretch - like ukulele strings - but once the stretc has been taken up, they stay in tune very well.
• 

  Yellowbelly Flatt September 22, 2011 at 6:06pm

  Oh, I forgot

  . Welcome to the Nation.

  It's the British cigar box festival next week, organised by the Home Grown Music Collective.