I have five builds ongoing at the moment, but my first build has encountered a bit of a stall.  The trouble is that I mistakenly cut the neck (which is not tapered) to the proper width for a typical fender nut without taking into account the hardtail adjustable bridge's string spread.  Alas, it means that I will not be ending up with the six string I was aiming for, and it will have to be a four string instead.  I had an idea that even with four strings, perhaps I could still put a Bigsby style tremolo/Tune-O-Matic bridge combo on it, but I'm having trouble finding something that meets my needs.  So here's my question:

By chance, do any of you gurus out there know where I can find a suitable hardtail 4-string bridge (but a Tune-O-Matic plus compatible tremolo would be super awesome - IF possible) that will accommodate a string spread of 35mm (12mm between each string)?  (The neck is 47mm wide.)  My concern is that the neck is too wide for 10mm spacing and I would like for the strings to still be able to rest over the poles on a pickup without having to go piezo on this particular build.  I can get pickups with 12mm spacing, but I'm having trouble finding a bridge that will meet my needs.

I've seen the adj. 4-string bridge at CB Gitty, but their page says it's a bottom loader, which is a problem for the box I'm using (very thin back on the guitar body).  I looked at the same bridge elsewhere and one page suggests that the plate to the bridge can be drilled so that the balls of the strings could be retained directly by the bridge plate rather than running the strings through the body with ferrules.  Has anyone tried this with any success?  Thanks a million for any advice you fine folks can offer.  I REALLY don't like the idea of cutting down my one-piece mahogany neck from a 6 to a 4 but I see little other option.

DSC_0270.JPG

DSC_0271.JPG

You need to be a member of Cigar Box Nation to add comments!

Join Cigar Box Nation

Email me when people reply –

Replies

  • You could go to tail piece and a floating bridge instead. You can use any string spacing between between bridge and nut. How about a five string?

    GEDC5975.JPG

    • Ah!  I SEE!!!  Okay - I wasn't aware I could get away with wood on the tremolo or on a dovetail!  I appreciate the ideas greatly and you guys may have just helped me save my no.1 build!  Thank you guys

  • hummm..  how energetic  do  ya  feel  ? 

    306556966?profile=RESIZE_1024x1024

    306558068?profile=RESIZE_1024x1024

    • That's schweet!  I could probably pull that off - what kind of wood did you use on the bridge and trem?  That is one cool looking axe, brother!  B-)

      • oak arm  and  sides and   not  sure  on the dowel  .  but   under that  lower  dowel  , i  have a metal  rod   for support  , otherwise   the tension would rip  that dowel    right  outta there  .  this  type   of  trem  was a  bit of a  pain in the ass  ,  so  .. be  warned  ,  you  may   want  an  easier solution  if  just  starting   out   . 

        • I am indeed just starting out but I have mad skills when it comes to engineering wood.  Thanks for the insight - I have one question:  How does the lower arm (the one supported with steel rod) attach?  It appears from the picture that the wood cover rests on top of the sides - so does the metal rod run through holes in the side pieces?  I can't figure how it is fixed on there.  As far as measurements go, I have a friend with several Gretsch guitars and Bigsby trems to put a dial caliper to.  I like your idea and I think I might imitate your work.

          • you   got  it  . the wood dowel   is just  glued  ontop  to   hide the  bar  under  it  which is  as  you said run through the side holes  ;-) it hides  the front screws too  (somewhat  )  ;-)

            another  tip  .   - rub regular  pam cooking  spray on  the top  dowel  ends  for  less friction  . 

            also  .  as per  size    , to  give  you an idea  . i   used  an oak cbg fretboard to  cut out  the sides and  the  bar  . 

            you are welcome to  copy / imitate  it  .  its not  part of my   swamp witch guitar  line  , so  have at  it  ;-)

             

            • Shoot - I forgot to ask about the spring - is it the same part used on the mass-produced Bigsbys?  Thanks again, brother!

              • teisco  replacement spring off ebay  actually  ,  but the  bigsby  spring  should  work  too  . 

    • That bridge is great, that's a cool git.

This reply was deleted.