I seem to remember seeing a post somewhere (maybe facebook) about someone using fine nails as fret wire.
Any thoughts or has anyone tried it with success?

Views: 107

Replies to This Discussion

Dont panic! Just found a previous post
Half a long split pin and super glue ?

There are several who seem to use these with much success. I tried this, and bobby pins on two of my earliest of builds. The bobby pins worked, but were simply glued to the fretboard (no clean way to do it... lots of squeeze out with no good way to clean the board after the glue set). The nails were a pain in the butt, made the frets too high (similar to how a scalloped fretboard acts if you are used to applying full pressure). Everything fretted sharp, despite the intonation being set somewhat correctly.

I would go with traditional frets over anything else.

I use bobby pin frets, as supplied on my custom SwampWitch by the anonymous pick. They are easily replaced with a VERY SMALL amount of CA glue. If you are careful, there's no mess. You're using far too much glue if you have extensive squeeze out. A small dot is all you need. And I can get 200-400+ frets from a 100 flat bobby pin pack for around 5 bucks.

Here's what they sound like:

http://www.cigarboxnation.com/video/oily-s-guitar-lounge-6-take-an-...
Working on an experiment at the mo, initial thoughts are like Brian said and they'll end up sitting to high. But you never know unless you try. Ill post some pics at some point too
Still need to cut to length, which thinking about it now i should have done before glueing them on! But im inpatient and its an experiment ☺
Attachments:
Well, the flying pig is pretty much finished! Still need to adjust the bridge to get the string height right. But other than that its ready to go to its new owner. Im now in two minds as to whether i'll try using finishing nails again or just buy some fret wire. Picked up a nice set of needle files today which will hopefully help set the depth right if i do decide to use nails again.

I have used them and they work ok but they can be hard to set in straight.

RSS

The Essential Pages

New to Cigar Box Nation?How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Discussion Forum

Nails for frets?

Started by Mike. Last reply by Alan Robinson Aug 1, 2017. 8 Replies

Flea market finds

Started by Mike Jul 24, 2017. 0 Replies

Not just a lolly stick

Started by Wade Jan 2, 2015. 0 Replies

Save that box screw up!

Started by Wade. Last reply by Thomas "Duck" Petry Dec 4, 2014. 2 Replies

CB string height gauge

Started by Wade. Last reply by Wade Jul 9, 2014. 2 Replies

Recycled stuff

Started by Keith 66 Jun 11, 2014. 0 Replies

Free recycled Piezo pickups

Started by Wade. Last reply by Rob Brighton Jul 3, 2013. 19 Replies

Joining Lumber

Started by Where's Uranus?. Last reply by Mark Lindsay Jun 4, 2013. 8 Replies

Fretboard radius

Started by Wade. Last reply by rusty case Feb 11, 2013. 1 Reply

Free grounding foil

Started by Wade Feb 10, 2013. 0 Replies

Free Fret dot markers

Started by Wade. Last reply by Mark Lindsay Feb 3, 2013. 23 Replies

Recycled tonewood

Started by rusty case. Last reply by rusty case Nov 21, 2012. 13 Replies

Low $ substitute for banjo face?

Started by rusty case. Last reply by rusty case Nov 18, 2012. 6 Replies

Cheapo strings

Started by Karl G. Siewert. Last reply by rusty case Aug 27, 2012. 4 Replies

Hand saw.

Started by Wade. Last reply by rusty case Aug 27, 2012. 2 Replies

Tennis, anyone?

Started by Order99. Last reply by Order99 Aug 18, 2012. 4 Replies

1/2 Priced Nuts and Saddles

Started by Claude. Last reply by Order99 Apr 8, 2012. 10 Replies

Sources of bone for nuts/etc...

Started by BT Cohosh. Last reply by Karl G. Siewert Mar 15, 2012. 13 Replies

Cheap and easy bottle neck slide polisher

Started by Steve Becker. Last reply by Jeff Powers Jan 29, 2012. 7 Replies

Tuner preference

Started by Earl William Birth III. Last reply by Wichita Sam Mar 25, 2011. 3 Replies

Blog Posts

3. German CBG Festival

Posted by Markus Gaiser on September 16, 2018 at 3:42pm 1 Comment

..absolute authenticity!

Posted by billy jones bluez on August 18, 2018 at 10:30pm 0 Comments

Other woodwork

Posted by Tom E on August 16, 2018 at 5:00pm 4 Comments

kannel/ kantele (Baltic psaltery)

Posted by Tom E on August 16, 2018 at 1:00pm 4 Comments

Latest Activity

Rose Ericson liked the anonymous pick's video
6 minutes ago
Rose Ericson liked the anonymous pick's video
6 minutes ago
Paul Craig replied to Taffy Evans's discussion One of my cheapest sold......$800.00
"That's fantastic Taff."
10 minutes ago
Paul Craig liked Taffy Evans's discussion One of my cheapest sold......$800.00
11 minutes ago
Paul Craig liked Blues Frog's discussion The first sale
11 minutes ago
Paul Craig commented on Wal Callaby's photo
Thumbnail

The Pre-amp Hack

"Good job, it look's great."
14 minutes ago
Paul Craig liked Wal Callaby's photo
15 minutes ago
Paul Craig replied to Andreas Fischer's discussion Questions about Bodys (No Cigarboxes)
"I love these."
18 minutes ago
Paul Craig replied to default's discussion Need 3 string shovel help
"Good to know they are available. Really wanted others to know and look out for the plastic handle…"
25 minutes ago
Tim Hooper replied to Hans's discussion Glue for carbon fiber rods?
"I'm another model aeroplane builder.  Most model/hobby shops here in the UK sell carbon…"
1 hour ago
Tim Hooper replied to Andreas Fischer's discussion Questions about Bodys (No Cigarboxes)
"I've had success using old guitar bodies, cut down in size. Two ukes so far, with a…"
1 hour ago
Omar Mariani and Bjorn Damsgaard are now friends
1 hour ago

Music

Loading…

© 2018   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service