Reworked Version w/ upgraded Power switching:

Views: 1115

Replies to This Discussion

If you want a cleaner amp, then change C2 to 470uF & leave pins 1&8 open on LM386? 

 Thank you for this, Brian! I never installed any volume pots into my CBGs.  MInd if I ask how one would go about adding a volume pot to this circuit?

From the Datasheet:

Upgrade to External Power:

 Thank you Brian! You rock!

 I am nearly finished building the version of this amp at the top of the page. Question... Why the little "U"-turn at the end of the positive speaker trace and not in the one at the bottom? I'm going out on a limb to risk sounding stupid, but is it to add a little resistance to that part of the circuit? Or, can I just run it straight off the edge of the board like the second, (revised) version?

 Thanks for any assistance you guys can give,

Ray

You could, it was just an extra solder pad?

OK, thank you very much! I am just making it harder than it is, I suppose. I presume nothing when it comes to electronics. I know next to nothing about it. 

Thanks again, Brian!

Howdy all!

 I was pulling the capacitors out to finish building this amp and noticed that of the dozen capacitors that I had bought, one was not a 16+ volt version, but a 10 volt. I remember seeing most places that amps like this use 16 volt capacitors. I was hoping one of you could/would enlighten me. The amp will not get anything bigger than a 9 volt battery or six AAs. Can I get away with the 10 volt cap or should I wait until I can get the 16 volt?

 Thanks in advance for any help.

Ray

If you’re using batteries they won’t have any problems? Generally, most use a voltage rating of around double or more than the operating voltage, just to be on the safe side. But, you’re not using an unregulated wall wart , so no worries?

 Cool beans. Looks like I am in luck. Thank you again, Brian. You ROCK.

 Off I go to the shop...

 Finally, after delay after interruption after delay, I got one of these to power a CB Gitty speaker and it sounded pretty good. Today I unhooked the speaker and soldered on a 1/4 in mono jack and put the amp between one of my CBGs with one of my homegrown low-z pickups and my Micro-Cube, with the LM386  as a pre-amp and ... wow... The difference is HUGE! Thanks guys again! This is exactly what these low-z pickups need when they need to be louder and overdrive an amp more. I'll try to get a sound file or two out in a day or so.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Discussion Forum

Tribute amps I've built

Started by Tom Hoglund Nov 7, 2022. 0 Replies

LM386 Amp w/ Switchable Clean Channel

Started by BrianQ.. Last reply by BrianQ. May 28, 2021. 1 Reply

Simple 1st Timer CBG Amp

Started by BrianQ.. Last reply by BrianQ. Sep 27, 2020. 25 Replies

Matching Speakers to LM386

Started by Southern Ray. Last reply by Southern Ray Aug 6, 2020. 11 Replies

Suggestions wanted for easy amp build

Started by Southern Ray. Last reply by Southern Ray Jun 15, 2020. 11 Replies

Ruby Amp

Started by BrianQ.. Last reply by Southern Ray May 16, 2020. 27 Replies

Low-Z pickup and components values

Started by Southern Ray. Last reply by Southern Ray May 13, 2020. 6 Replies

Oops

Started by Southern Ray. Last reply by Southern Ray May 2, 2020. 12 Replies

DIY Spring Reverb

Started by Kevin Keating. Last reply by Paul Craig Oct 17, 2019. 4 Replies

TDA2030A Amp

Started by Bama Hound. Last reply by Gary Stenzel Jul 23, 2017. 14 Replies

Home Brew Champ Tube Amp

Started by Scott aka Farmer Ted. Last reply by Paul Craig Feb 6, 2017. 3 Replies

Dual IM386 Chip amp

Started by Paul Craig. Last reply by Paul Craig Jan 26, 2017. 29 Replies

5 Watt Amp Kit (DIY Case)

Started by Walter Haapapuro. Last reply by Gene Jones Dec 7, 2016. 46 Replies

DIY reverb behold - I found this online

Started by Danny B.. Last reply by Paul Craig Nov 2, 2016. 3 Replies

Bass Cabinet project

Started by Murdoc_420. Last reply by Murdoc_420 Jul 15, 2016. 34 Replies

Kalamazoo Model 1 Deluxe

Started by Scott aka Farmer Ted. Last reply by Rick Alexander Jun 20, 2016. 12 Replies

LM386 amp and other stuff

Started by Denis U. Last reply by Denis U May 29, 2016. 19 Replies

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->