I know about using bird shot, bb's, short brads, small pieces of broken glass, even course sand to prevent the pieces from sliding around. But I just watched a video where he(sorry pc incorrect) used tablesalt sprinkled on the glue for the same purpose! Has anyone heard of or done this? Wouldn't the salt cause  deterioration of the wood fibers? Wouldn't sugar be a better option? Personally I wouldn't use either one! Hmmm, how about "Grapenut cereal"? It's hard enough to break teeth!

Views: 215

Reply to This

Replies to This Discussion

I always used a tack.,.,and I kept reading about using salt for years.,.,so I tried it.,,.pff.,.,  I think its some kind of urban legend.,,. 3 grains of salt.,.,??   When I added a little salt to the joint the Titebond glue assumed the feeling and grit of micro-mortar.,.,total BS.,.,.I had to scrape the joint clean, use fresh glue and a tack.,.,.,I would never do it again unless I was just trying to punish myself.,.,.,

My grandfather used all the methods I mentioned earlier with the exception of the brands and salt, those cost money.(long story) How are you using tacks? Lying them on their side like mini splines or pressing the heads into the wood with the points up?

The only place i need to stop the sliding is in the scarf joint of the neck/headstock. I drill a small hole with the joint dry, add the glue, then the tack. Clamp till dry, then pull the tack. The finger board covers the tiny shallow hole. In hindsight, I could use a toothpick instead of the tack, and just leave it there.,

Gotcha! Have to give it a try. Since its being covered anyway I'd use the small bamboo skewers, I use them for screw holes.

I've heard of it in several places. It usually says "a few grains" whatever that is. So, it may not be enough to cause deterioration of the glue. I find it irrelevant since there are so many other options that work. I still find the use of a single tack just to hold it steady until the clamps are in place. I put glue on both surfaces, scrape off the excess and let it get sticky before mating the pieces. Haven't had a slipped scarf joint in a long long time.

In the vid he used a salt shaker, although very small amount. Grandpa had a Chock full of nuts coffee can full of fine broken glass, but he also still used powdered glue.

Yes, letting the glue tack up is the best way to avoid slipping on any kind of joint?

Yea, what BrianQ said...

I've used salt, for use on fretboards and the scarf joint. about 10 grains of salt 3" from each end of the fretboard centered. On the scarf joint I have placed salt dead center, squeeze clamps at each end then a C clamp in the center.  No slipping and  no glue was fouled. I think it works great. I keep a salt shaker in the shop.

Didn't mean to sound cynical, just never heard of it.

Here's a trick I imagined in my head and ended up working so well I use it for anything that may need help with slippage...

Take a staple gun and put a staple where the join will be. Use your fret snips to snip the embedded staple on each of the ends, removing the middle. You may have to raise the staple out a bit to do this - which is fine (you really only want the staple to go in halfway). What you have now are two sharp metal posts. Apply your glue over the area and press the other piece of wood onto the posts and clamp up. The staple will hold the joint enough to prevent slippage, it won't interfere with the join, and you'll never see the work.

I've actually modified a staple gun so that it only puts a staple in halfway, just for these types of joints.

Cheers!

I like that idea better than trying to hammer in those tiny friggen wire brands and nipping off part of it. Thanks for the tip.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

BrianQ. commented on Dar Stellabotta's video
42 minutes ago
BrianQ. liked Dar Stellabotta's video
44 minutes ago
Southern Ray commented on Southern Ray's photo
Thumbnail

Project Punch!

" Thank ya again Keith!"
2 hours ago
Southern Ray commented on Southern Ray's photo
Thumbnail

Punch Project!

" Thank Ya Keith!"
3 hours ago
Doug Thorsvik commented on AGP #'s photo
Thumbnail

AGP #527 - ''Led-Zep 2''

"This build really strung you along Alan! Reminded me of all my fishing line experiments; a lot of…"
4 hours ago
Doug Thorsvik commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Diggin’ the slow blues. I like that last pic Andries! Look at all those cool guitars. Yeah!!!"
4 hours ago
Dar Stellabotta posted a video

A Cigar Box Guitar Six Stringer Built by Louie Lamanna

This video is the unboxing and the demonstration of a beautiful, six stringer built by Louie Lamanna. Join Louie and I June 15 at the second annual Pittsburg...
6 hours ago
Doug Thorsvik commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter to you too Andries! The passion is definitely in full swing. Turns out I’m…"
6 hours ago
A.D.EKER commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter Doug ! the Passion is in full swing !"
7 hours ago
A.D.EKER commented on Ricky D's photo
7 hours ago
A.D.EKER commented on A.D.EKER's video
7 hours ago
Keith Rearick liked Doug Thorsvik's video
10 hours ago

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->