Replies to This Discussion

Permalink Reply by Fantacone Box Works on July 17, 2019 at 5:40am

I agree. The handle is a oak cabinet pull. It would be "over" where the piezo pick up is glued on. My measured bridge height is 5/8 + a fret on top. I think the handle is gonna be to high. Im sure he ordered it so now i got to wait till he drops it off.

Mike 

• ▶ Reply

Permalink Reply by the anonymous pick on July 16, 2019 at 12:28pm

A few  other options .

 -Get another box the same . cut out the exact spot  where the bridge covers , and  use that as your bridge so it has the same matching print. ( you could also duplcate that part of the print and apply to bridge)

- Do you have room to offset the neck to pass beside  (above or below) the logo ? 

• ▶ Reply

Permalink Reply by KOOL DOG HOOCH on July 16, 2019 at 1:18pm

What an neat idea they wanted unique an offset neck would check both boxes, uniqueness and label preservation. Pick you never cease to amaze me. Would that be considered "thinking outside the box"?

• ▶ Reply

Permalink Reply by the anonymous pick on July 16, 2019 at 4:35pm

lol.. quite the opposite actually ,,  Sometimes we have to remember...  it is just a box .. and not to overthink it .. especially in the form of "advise" .  ;-)

• ▶ Reply

Permalink Reply by the anonymous pick on July 16, 2019 at 5:14pm

EDIT... By the photo he just posted , it looks a lil late for an offset neck . 

• ▶ Reply

Permalink Reply by Fantacone Box Works on July 16, 2019 at 7:01pm

• Neck has slight built in offset. I drop the rear 1/8" or a little more. Looks like the bridge will be edge of the O and M. 

• ▶ Reply

Permalink Reply by the anonymous pick on July 16, 2019 at 7:07pm

cool .. not to mention .. a lil  magic marker / ink pens/  paint /  wood burners ...etc .. goes a long way ....

• ▶ Reply

Permalink Reply by Fantacone Box Works on July 17, 2019 at 7:19am

WOW!

• ▶ Reply

Permalink Reply by François on July 17, 2019 at 9:21am

Putting the lid on a color copier would produce a duplicate that can be applied to a scrap piece of wood in order to camouflage the whole thing.

• ▶ Reply

Permalink Reply by Taffy Evans on July 16, 2019 at 1:44pm

Hi yet again, sorry. That's a good idea from pick. Why I came back was to address your question, how far from bridge to tail. Ideally,for good sound, the briidge sits as close a practicable in the middle of the effective vibrating area of an instruments top. Thus genererating  the best tone and volume. 

Putting the bridge close to an edge, either a side or the tail, will limit the quality of the sound. I have put bridges in from the tail at about 50mm and found the output wanting. I always try for halfway to one third of the box away from the tail. Normally about 100mm to 120mm.

Taff

• ▶ Reply

Permalink Reply by Taffy Evans on July 16, 2019 at 6:40pm

Not again....yep this may be useful........while waiting for a glue up to dry I tried my Perspex bridge idea and it only took 10 minute to make out of scrap. What you cant read from one angle you can see from another. I'm so pleased at the way this worked out I'm going to use it in the future.

All the writing you see is on the box not the Perspex.

Taff

• ▶ Reply

Permalink Reply by Fantacone Box Works on July 17, 2019 at 7:36am

Nice! Great ideas, thanks. After all this hes ok with what i normally use

Mike

• ▶ Reply

• ‹ Previous
• 1
• 2
• 3
• Next ›
• Page