Does anyone have good experiences working with a spokeshave to carve necks? I picked one up but I apparently just don't know how to use it right - it bounces and stutters, gets jammed full of shavings, and just generally doesn't get the job done the way I see it working in all the videos I've watched.
Any pointers, tips, advice?
Tags:
I use a spokeshave for the basic shaping of a neck (i.e. rounding). It does a good job of removing material quickly. What I found when I first got it was that I didn't know how to adjust the blade for good cutting.
Try lowering the blade into the spokeshave body until just a tiny amount of blade is sticking out of the body. You don't want to remove big chunks of wood, just little shavings.
Practice on a piece of one-by pine. Work on the 3/4" edge until you get a feel. Try cutting in one direction on the pine, then the other direction. You should see and feel a difference. Keep working with the blade depth until you get to a cutting depth you are comfortable with.
It is a good tool, but you need a bit of practice to get the tool and your technique sorted out.
No expert but I have used on with some success
1. Is it sharp?
2. If it bounces and stutters are you going against the grain, try the other direction
3. Are you trying to take too much off on one pass?
4. Apparently its a push tool, although do pull it.
See the link below, note the support jig.
what the other guys have said. i used one to make a bow years ago. its not a plane dont take too much with each pass. keep it sharp and keep it flat to the wood. i had more luck drawing towards me than pushing it away from me. is yours a flat bottom or is it curved? they come in both types.
i would still use a rasp to do the heavy work then the spokeshave to finalise shape before getting down to the nitty gritty of sanding it smooth.
Thanks for all the replies - a couple followup questions:
1. How does one sharpen the blade? I'm assuming it's just a matter of taking it out and using a file?
2. Are there any general pointers on how to determine how far the blade should protrude from the body?
I also had more luck drawing towards me than pushing it away.
1. Don't use a file you will ruin the cutting iron.
You should use an oil stone or wet stone; you can use fine sandpaper stuck down to a very flat surface. Plenty of how to guides on the internet.
2. I set it t so barely protrudes, and then adjust in small increments until it the taking of a fine shaving. Test of some scarp.
I have used both the spokeshave and drawknife and for me, some pieces work great and some just don't work at all. As others said, going the opposite direction can help too if it is catching the grain of the wood.
For your second question, it can stick way out too. Then it acts more like a scraper and no worries with shavings building up. It is a tool that takes some playing with to get the hang of it.
Which one did you buy?
As for sharpening...you need a honing guide like this one - Robert Larson 800-1800 Honing Guide
I tried doing it with out a guide and I'll never do that again. Trust that you need one.
Then you'll need some sand paper or better yet a sharpening stone.
I like these - DMT W6XP 6-Inch Diamond Whetstone Sharpener I also like the
Japanese whetstones.
So a Honing Guide and some sand paper is good enough.
So, I followed your advice and picked up that honing guide - and found that my spokeshave blade is too shallow to work with it! :-D - the blade isn't long enough to protrude far enough to get the 25 degree honing angle. Oh well! It will still be useful for chisels - but it's back to the drawing board as far as finding a guide for the spokeshave blade...
Hi, like all cutting tools they have to be as sharp to do their intended job well. I test mine...if I can shave hair of my arm, I'm happy.
However, the angle of the cutting edge also contributes to smooth cutting, harder wood often requires a different angle to softwoods.
A starting point for setting up the blade, as I was told as an apprentice, was to sight down the soul plate of my plane and I want to see a thin black line (the cutting edge of the blade) protruding from the slot in the sole plate. The same should work for your spokeshave.
As already mentioned play atttention to grain direction.
Taff
Hi Dean, crap happens but don't give up, I'm a firm believer in "try another way". I do not know what type of sharpening guide you have, but I bet there's a way to modify it.
i'm thinking of a hardwood insert that fits in like a chisel but has the meens to hold the spokeshave blade on its end and up against the oilstone. I have it sorted here. Give it some creative thinking.
Think outside of the cigar box. Ha ha.
Taff
Started by Timothy Hunter in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray yesterday. 1 Reply 2 Likes
Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies 2 Likes
Started by Taffy Evans in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 10. 1 Reply 3 Likes
Started by Cigar Box Nation in Feature Articles. Last reply by BrianQ. Mar 9. 4 Replies 3 Likes
Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies 1 Like
Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies 0 Likes
Started by Ken I in Building Secrets, Tips, Advice, Discussion. Last reply by Brian partington Mar 8. 8 Replies 0 Likes
Started by Southern Ray in Cool gear discussion - that's not cigar box related. Last reply by Southern Ray Mar 6. 5 Replies 0 Likes
Started by Taffy Evans in Other stuff - off topic, fun stuff, whatever. Last reply by Taffy Evans Mar 5. 4 Replies 2 Likes
Started by Nomad Jack in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray Mar 2. 6 Replies 1 Like
Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Carl Floyd Mar 1. 15 Replies 0 Likes
Started by Joe in Performances, How to Play, Lessons, Concerts. Last reply by Carl Floyd Feb 29. 13 Replies 0 Likes
Started by Chance in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Feb 22. 12 Replies 1 Like
Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies 4 Likes
Started by Brad in Cool gear discussion - that's not cigar box related. Last reply by Southern Ray Feb 19. 6 Replies 3 Likes
Started by Jacob Shook in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Feb 16. 10 Replies 0 Likes
Started by Southern Ray in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray Feb 16. 2 Replies 0 Likes
Started by Skeesix in Performances, How to Play, Lessons, Concerts. Last reply by Skeesix Feb 6. 2 Replies 1 Like
Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Steve M Jan 31. 9 Replies 0 Likes
Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies 0 Likes
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
Posted by billy jones bluez on February 8, 2024 at 4:05pm 0 Comments 0 Likes
May 11, 2024 from 11am to 8pm – Speakeasy Grill
0 Comments 0 Likes© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!