Any body have a clue why I get this loud squealing feedback through the amp when I try to turn up the volume? It is not corrected by moving further from the amp. This is a piezo pickup mounted to the underside of the lid.

Views: 1162

Replies to This Discussion

The piezos do appear to be quite sensitive to amp settings. I find that if I have any of the controls up too high, feedback is quick to occur. Any overdrive setting appears to be critical.

Folks have tried various dodges to avoid this; mounting the piezo on a piece of foam, isolating it in silicone gel...etc.
Thanks Mark. Sure to give those a try. I'll have to experiment i guess to find the best solution.
Does this drop the pickupability (like that word? lol) Is it totally encased in gel or caulk?
I use Dap weldwood contact cement. I have not had a issue with any feedback. If anything I definatly get an all around better sound. Just add a bit to both contact points with a brush, then join, press down ever so gently and hold for 20-25 seconds. Lift the piezo off and hold for 30 seconds. Then press the piezo back on, and Swirl(tech term for rub it around in circles) the piezo on the surface (this will guarantee total contact) for 5-10 sec and hold gently you are not a bear dont act like one. It takes about 15 -20 min to dry. After a solid 2 min of holding you can let go, if it slips hold longer.
Wesley Dean
As a newbie, can someone explain the do's and dont's of piezo encasement? I cant quite figure if the whole thing is completely encased in contact with its 'encaser' (probably not the correct terminology lol) , or if the piezo should sit in a cavity so its encased, but with nothing touching the face?
Generally, you want really good mechanical connection to the strings (i.e., the bridge saddle) and as little connection to the box as possible. That will minimize feedback. So direct contact with the bridge and foam separating it from the box.

As a practical matter, piezos naturally have some brittle high freq stuff that's hard to control down the line. It helps to put something that mechanically absorbs high freq between the piezo and the bridge. (I use a rubbery, space filling, jewelry glue so there's a layer of the glue to mechanically insulate the piezo.)

Wiring two piezos in series will also help tame the high freq.

After trying everything, what I actually do most of the time is use 1 piezo, glued with a blob of jewelry glue, inside the box right under the treble foot of the bridge. No need for foam since the air in the box actually insulates the piezo from any extraneous movement in the box (piezo's don't pick up air movement very well). No feedback problems at the moderate amp settings I use on stage. They would feedback in front of a stack turned up to 11 - If I played that way, I would fill the box with foam to prevent it vibrating at all and build the piezo into the bridge ... or just use an electromagnetic pickup.


RandyRoosterGuitars said:
As a newbie, can someone explain the do's and dont's of piezo encasement? I cant quite figure if the whole thing is completely encased in contact with its 'encaser' (probably not the correct terminology lol) , or if the piezo should sit in a cavity so its encased, but with nothing touching the face?
Thanks to everbody for the feedback..I'm very grateful. Rock on!
One possibility is you may have a resonant enclosure problem.

For instance the RS 273-0073 is spec'd to have a resonance of 2500+/-500Hz. The center frequency of 2500hz has a wavelength of 1100f/s / 2500/s =0.44ft = 5.28". The range is 2000Hz to 3000Hz, so the range of sizes can go from 4.4" to 6.6" .

If this piezo transducer is placed in the center of a 5.28" wide box there is a strong probability it will squeal at 2500Hz if it gets enough feedback from the amp.

The solution is to move it off center. This has the unfortunate side effect of changing the tonal response.

What is the size of your cigar box?

Sven.
Damn Sven thats all too technical for me, but it was an 8 in. sq. box

Sven Pfitt said:
One possibility is you may have a resonant enclosure problem.

For instance the RS 273-0073 is spec'd to have a resonance of 2500+/-500Hz. The center frequency of 2500hz has a wavelength of 1100f/s / 2500/s =0.44ft = 5.28". The range is 2000Hz to 3000Hz, so the range of sizes can go from 4.4" to 6.6" .

If this piezo transducer is placed in the center of a 5.28" wide box there is a strong probability it will squeal at 2500Hz if it gets enough feedback from the amp.

The solution is to move it off center. This has the unfortunate side effect of changing the tonal response.

What is the size of your cigar box?

Sven.
Wrap your peizo in a hanky inside of the guitar. Now the peizo floats in there and it is not touching anything, but it also picks up the sound too as well. It does give the box a deeper tone as well.
Piezoelectric transducers seem inherently "tinney". I have used a capacitor across between + and - wires. the one I tried is called an "Orange Drop". It it like turning the treble way down. The bridge seems to be a good choice(as opposed to a "top"). It might be cool for some, to use a neck or even peg-head placement.(gets fret/left hand percussion). A blend knob could be used. I don't know much about capacitors, just salvaged a bunch and test. I sort in three piles, 1. no effect, 2. no sound, 3. tonal modification. Some of my experiments with phonograph cartridges has been profitable. There again they use a tone modification. I took one out of the turntable. I think I will soon use a whole tone arm, just for the "look"of it.
Did anyone try making a feedback-bucking piezo pickup by connecting two piezo pickups out of phase?

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Discussion Forum

Piezo feedback problems

Started by David Fultz. Last reply by Bernie Edwards Aug 27, 2016. 14 Replies

Bowed instruments

Started by Fomhorach. Last reply by JL Mar 23, 2016. 1 Reply

Ceramic piezo disc as a mic for a reverb spring

Started by Jon Leslie/Runaway Veal Music. Last reply by Fomhorach Feb 29, 2016. 6 Replies

Distortion

Started by Kevin M. Kraft. Last reply by Fomhorach Feb 28, 2016. 16 Replies

Stomp box

Started by smojo. Last reply by JL Jan 4, 2016. 14 Replies

DIY Tremolo

Started by Better Trees. Last reply by Better Trees Mar 10, 2014. 4 Replies

wiring mystery

Started by bucky. Last reply by Bernie Mango Feb 28, 2014. 5 Replies

Fever dream pickup

Started by Bear Peterson Jan 23, 2014. 0 Replies

Ted's Headstock Designs

Started by Ted Crocker. Last reply by Ted Crocker Sep 1, 2013. 2 Replies

Fretting Tips, Tricks & Supplies

Started by Ted Crocker. Last reply by Silent Jim Dec 21, 2011. 1 Reply

How to Find the Center of a Dowel or Circle

Started by Ted Crocker. Last reply by Ryan Rose Nov 6, 2011. 1 Reply

Nut & Bridge Slotting

Started by Ted Crocker. Last reply by Mark Werner Oct 18, 2011. 1 Reply

Printable Harbor Freight Tools Discount Coupons

Started by Ted Crocker. Last reply by Bear Oct 17, 2011. 1 Reply

Ted's Wiring Diagrams & Schematics

Started by Ted Crocker Oct 17, 2011. 0 Replies

Identifying Exotic Woods

Started by Ted Crocker Oct 17, 2011. 0 Replies

not cbg sorry

Started by jon beel. Last reply by ian dawson Sep 28, 2011. 3 Replies

circuit sniffing

Started by petey twofinger. Last reply by Chuck Dubman Jan 4, 2011. 3 Replies

2 prong outlet guitar chord?

Started by Jerryrig240. Last reply by Chuck Dubman Jan 2, 2011. 6 Replies

beer bottle caps

Started by smojo. Last reply by Nick Jan 4, 2010. 8 Replies

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->