I'm in the middle of building an amp using a basic LM386 with a 10uF cap on pins 1 and 8 to increase the volume. It's OK, in fact good, but I want that little bit more, so I got the LM386 n-4 IC which says it'll give me 1 watt. It doesn't give me any sound at all.

Before I cut out the cap and mess with something that does work, can anyone please tell me if that cap mod works on all versions of the 386, have  got a dead chip, or am I missing something else?

Thanks

Denis

Views: 468

Replies to This Discussion

The LM386 IC in all forms (N1, N3, N4) work in an amp circuit. The major difference is the input power supply ratings and power output.

If you have wired the LM386-N4 as shown on your schematic and you still get no sound, check all solder points and your grounds. Something physical is likely the problem.

With a maximum power source rating of 18vdc, you will need to power the amp with a fully regulated wall wart adapter, or figure a way of wiring two 9v in series, or twelve "AA" batteries...

Some time since this was brought up, but wanted to let you know that the 386N4 chip needs more voltage than the other 386 chips to work. The N1, N2 and N3 work on 9volt to 12volts while the N4 needs 14volts to18volts. That could be your problem if you were trying to run it on 9volts. Also the N4 chip can put out 2watts compaired to the others 1watt output.

Denis, the 10uF capacitor between pins 1 & 8 are to increase gain, not volume. If you omit the capacitor, the preset gain of the 386 chip is 20. Using the capacitor increases gain to 200.

Voltage rating of the cap, if used, is typically 16v up to 35v. And it can be either radial or axial, and it should be polarized, with the + to pin 1, the - to pin 8.

But, as Paul and I have stated previously, the N4 version of the LM386 needs more power to operate.

I just recently built 2 LM386n-4 boards and used a used 9 volt battery to test them. Both worked great. Each schematic was from the internet and used different values of caps and resistors. I set both up to give the 200 gain on pins 1 and 8. Plenty loud from the 8 volts I measured from the battery. I'll try 12 volts and see what it sounds like.

Richard

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Discussion Forum

Ruby Amp

Started by BrianQ.. Last reply by BrianQ. May 18, 2020. 6 Replies

Smokin' amp (literally)

Started by James Conder. Last reply by James Conder Aug 27, 2019. 4 Replies

Simple Headphone/Practice Amp

Started by BrianQ. May 16, 2019. 0 Replies

Problem with second-hand amp.

Started by Arthur Payne Mar 31, 2019. 0 Replies

Artec Amp Help!

Started by Jesse Lively Sep 10, 2017. 0 Replies

LM386 N-4

Started by Denis U. Last reply by Richard Haas Dec 3, 2016. 4 Replies

History Mystery--Orrtronic Tube Amplifier project

Started by Scott aka Farmer Ted Nov 17, 2016. 0 Replies

Dual IM386 Chip amp

Started by Paul Craig. Last reply by Paul Craig Nov 3, 2016. 31 Replies

Amp Speakers

Started by Primitive Acoustics. Last reply by Primitive Acoustics Mar 9, 2016. 3 Replies

Grounding for Cigar Box Amps: Chassis Ground?

Started by Erik Bell. Last reply by Scott aka Farmer Ted Dec 20, 2015. 4 Replies

Neat amp components

Started by Surly. Last reply by Alan Steeg Oct 27, 2015. 1 Reply

can a dab radio be turned into an amp

Started by Coventry Halfpenny guitars. Last reply by Pickedmoor Jon Oct 20, 2015. 3 Replies

SDA-T Questions

Started by alectron. Last reply by Zac Ray Sep 2, 2015. 10 Replies

HI - New guy & And speaker question

Started by Henry S. Last reply by Henry S Mar 25, 2015. 4 Replies

Are Pre-fabbed LM386 Moduals Worth Trying?

Started by Scott W. Last reply by Henry S Mar 24, 2015. 6 Replies

Powered sub to amp ??

Started by wormil. Last reply by wormil Sep 2, 2014. 2 Replies

Amp and speaker INSIDE the guitar?

Started by Greg Potts. Last reply by Ron "Oily" Sprague Jul 1, 2014. 1 Reply

trying to hack an old valve radio, into a guitar amp,

Started by GARAGE HERMIT. Last reply by GARAGE HERMIT Apr 29, 2014. 108 Replies

Best mini amp KITS

Started by MichaelS Country Boy Guitars. Last reply by Henrik Johansson Mar 10, 2014. 34 Replies

amp wiring help

Started by HarleyTodd. Last reply by Bernie Mango Feb 26, 2014. 18 Replies

Latest Activity

Dar Stellabotta posted a video

A Cigar Box Guitar Six Stringer Built by Louie Lamanna

This video is the unboxing and the demonstration of a beautiful, six stringer built by Louie Lamanna. Join Louie and I June 15 at the second annual Pittsburg...
5 minutes ago
Doug Thorsvik commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter to you too Andries! The passion is definitely in full swing. Turns out I’m…"
46 minutes ago
A.D.EKER commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter Doug ! the Passion is in full swing !"
1 hour ago
A.D.EKER commented on Ricky D's photo
1 hour ago
A.D.EKER commented on A.D.EKER's video
1 hour ago
Keith Rearick liked Doug Thorsvik's video
5 hours ago
Keith Rearick liked A.D.EKER's video
5 hours ago
Keith Rearick liked Doug Thorsvik's video
5 hours ago
Keith Rearick liked Ricky D's photo
5 hours ago
Keith Rearick liked Ricky D's photo
5 hours ago
Keith Rearick liked Ricky D's photo
5 hours ago
Keith Rearick liked Ricky D's photo
5 hours ago

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->