I don't claim to have invented this design, but here's how I make a robust neck through with a heel, leaving plenty of space under the lid for pickups/bracing etc. There are plenty of ways to go about this, and no right or wrong way. However this design helped me overcome a number of obstacles in my early builds. I will skip over quite a few basic aspects of CBG building so it might be an idea to have a grasp of scale lengths etc. first.

This article is not aimed at seasoned builders, but rather those who were just starting out. Or even more specifically, myself about 3 years ago when I started making these!

The only thing this diagram doesn't show is 'back angle', which I use on all of my builds to improve ergonomics. Just imagine the block at the front on the box is lower than the one at the back. It's that simple, and can make a big difference to how well a guitar plays. This, along with some other tips is covered in another how-to here.

So - you need a 1 metre length of hardwood, and a separate fretboard (6.5mm/1/4"). Cut the neck blank into 2 pieces. This will depend on the kind of box you are using. You want the upper piece to extend into the box by about 100mm, and the lower piece to extend roughly 40-50mm from the front of the box, creating an overlap of roughly 6"/150mm (see the picture above). You can use whatever headstock design you prefer, scarf etc.

The first job I do is cut and glue up the scarf joint. I cut the scarf using a jig and a big chop saw. Along with the Dremel and drill, these are the only power tools I use to make necks.

To glue up the scarf, I clamp the two pieces of the neck to the bench and then apply a clamp at the joint. If it slips, move the pieces back and try again. You want to get this right. Some people swear by sprinkling a little salt on the glue to stop it slipping. I haven't tried it myself. Once the glue has fully cured I slice off some material from the top side to bring the thickness of the headstock down to about 15mm.

While this is drying, time to take a look at the fretboard:

So at this point I've marked the frets using a metre ruler and Stew Mac's Fret Calculator, scored them with a knife and they're ready to slot. It is worth investing in a purpose made fret slotting saw and mitre box for this job. I've drawn a centre line and marked across the frets diagonally to place the marker dots. Carefully drill them out to the required depth. This would be much easier with a pillar drill but I don't have one.

Once the fret slots are cut, I taper the fretboard. This step is completely optional, but since trying it I have found it impossible to go back to square necks. If you want some tips on doing this, I wrote a 'how to' here. Once you're happy with the shape of the fretboard, you can add your side dots, if you wish.

In the below picture, I am gluing all of the remaining parts of the neck together; the fretboard, the lower portion of the neck that runs through the box, and the headstock 'wings' which will allow me to get a bit more creative with the design. These are made from fretboard scraps. 

I leave the neck in the clamps for 24 hours. I know many people would say this is unnecessary but I prefer to err on the side of caution. This is what it looks like after taking the clamps off. In this picture I have already used my mitre box to create a 'slope' where the two neck sections meet which will be the basis of the heel.

...and after tapering. Again, this is an optional step, and there is a 'how to' here.

So here's the neck so far. Time to get shaping - in part 2!

Views: 26986

Comment

You need to be a member of Cigar Box Nation to add comments!

Join Cigar Box Nation

Comment by Ducati Scotty on November 7, 2017 at 12:02pm
Great information, thanks very much!
Comment by Charles Z on August 21, 2016 at 11:47pm

very cool

Comment by Richey Kay on August 9, 2016 at 6:39pm

Hi Mike. This is just the design that works for me. I've been building CBGs with this design for a few years now with no problems. Yes, there is a glue joint, but good quality wood glues are very strong, much stronger than a single piece of hardwood which has been 'notched' out to fit underneath a cigar box lid. The string tension from 3/4 strings is not really a problem. It's when you start going beyond that that you need to build a bit more conservatively.

In short, it works for me!

Comment by Cigar Man Mike on August 9, 2016 at 5:26pm

Are you concerned about weakening the neck by building it in two pieces? While the design is neck-thru there are two glue joints, one in front and back, instead of a single piece of wood end-to-end. It would seem like all the string tension will be applied to these two joints. Great post and appreciate your comments!

Comment by Richey Kay on June 15, 2016 at 7:16pm
Thanks Toofy. Glad you're getting some use out of it!
Comment by Toofy Peg on June 15, 2016 at 4:08pm
Jesus man!! your a complete pro!! This is very useful info and thanks for sharing ! I've got lots to read yet and it's great 2 read and learn! Cheers
Comment by Richey Kay on March 22, 2016 at 4:36am
Happy to be of service David. I try to treat every box differently, I choose the box first, the make the neck. A one size fits all approach doesn't work for me either!
Comment by Dave McGrain on March 22, 2016 at 4:25am

This is great! I'm on my 4th build and neck building still is a bit confusing,mainly the in box part. I see people building necks for future builds and don't know if that would work for me but at the same time I'd love to have a back stock of necks so I can focus on my boxes.  

Comment by Philip Hale on March 6, 2016 at 12:28pm
Thanks for this, I am contemplating my first build and answers the problem I was anticipating.
Regards and many thanks Phil Hale
Comment by Joe Caruso on November 7, 2015 at 9:23am
Have never thought of doing the body as you've shown - solves a few questions I've had - will try on my current build, waiting for the glue to set on the scarf joint - many thanks for posting Richey.

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Apr 10. 14 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

Latest Activity

Glenn Kaiser posted photos
4 hours ago
Doug Thorsvik commented on Doug Thorsvik's video
Thumbnail

Da Do Ron Ron: 3D Printed Cigar Box Guitar

"Glad to put a smile on your face BrianQ! This one is a fun one to sing and play."
4 hours ago
BrianQ. liked Doug Thorsvik's video
5 hours ago
BrianQ. commented on Doug Thorsvik's video
Thumbnail

Da Do Ron Ron: 3D Printed Cigar Box Guitar

"Another great oldie I thought I’d never hear on cbg!! :)"
5 hours ago
Doug Thorsvik posted a video

Da Do Ron Ron: 3D Printed Cigar Box Guitar

Cigar Box Guitar Slingers - Spokane, 198th Zoom Mtg 04/15/24. Only 1-finger chords, free songbooks here: https://www.cbgslinger.com/download CBG Songbook.pdf...
8 hours ago
Matthias Bichsel left a comment for Moritz Voegeli
"www.cbguitars.ch auf FB This Bichsel"
yesterday
Matthias Bichsel left a comment for Moritz Voegeli
"Hallo, ich bin aus Solothurn. Lisa Stearns hat mich gefragt ob ich Dich kenne. Ich baue cbg. Gruss…"
yesterday
Matthias Bichsel liked Moritz Voegeli's profile
yesterday
BrianQ. left a comment for John Herrick
yesterday
BrianQ. left a comment for Daniel Cook
yesterday
BrianQ. left a comment for Skip Novakovich
yesterday
T-Gripped liked David Woodman 's photo
yesterday

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->