I used a straight poplar 2X1 for the neck (through neck) on my first build... it's straight until I put the strings under tension, then the neck bows slightly, but enough so the action is way too high.  Is poplar just a bad wood to use, or is there something I can do make sure the neck stays straight? 

Views: 2414

Reply to This

Replies to This Discussion

In my work I've found that poplar is a good wood to use for paint grade cabinet framework and columns and so on. I have never attempted to stain poplar because it doesn't take stain well, very blotchy like beech and birch. Mahogany is a good wood to use, also ash is good (very hard like oak, only better) and maple is good for a neck but its extremely squirly when you cut it on the table saw and if you don't have a brand new router bit it will leave a lot of burn marks which are a pain to sand out, cause it's so hard.
My favorites so far, 1. Mahogany for three strings, but for a six string I would use a truss rod.
2. Ash
3. Oak, if you can stand the smell, I can't.
I hope this helps Brian.
I have an cbg thats about 5 years old hasn't bowed yet. But I only tune it DAd or GDg not that much tension on the strings or neck. Could be you just got a bad piece. There are way to many here that have built with poplar necks with no bowing. Look at Shane Speals old mac 13 years old yes it has bowed a little but look at how old it is and how much abuse he has put it through.
Buying a finished 1x2 gives you a 3/4x 1 3/4 neck.
IMHO, I think poplar is to soft for that. Yes ... there have been many built, but still ... IMHO....
That said, I only use red oak 1x2's but I will use poplar when I do a fully carved neck. I start out with a 2x2 and end up with a hoss of a neck.
Even with red oak 1x2's I still pay close attention to the wood when I get it. I get the straightest piece they have .... I have left and gone to other places just to get one 1x2.
I also look at the grain. I only get sticks that have the grain running from end to end. The straighter the grain, the better. I have seen a 19" scale dulcibox with a 26" total neck-thru length bow with bad grain.
Paying close attention to the grain in poplar could help avoid the bow.

Matt
did you add a fretboard, or is the does the neck serve as the fretboard as well?
Poplar is not really a hardwood. Doesn't have enough rigidity for steel strings - might work with nylon, though. Best to stick with maple, walnut, oak, cherry, or hickory for necks - sometimes even mahogany 1 x 2 won't hold up under steel strings, but usually would work.
Thanks for the info guys... I should have added a pic, it's a 3 string (steel strings), no added fretboard although for my next build I'll be adding one. Godzilla, you're right about the stain part - it came out pretty blotchy, but what the heck, I see it looking a bit "different" as a plus.
Given the number of people who have used poplar with success, I prob just have a loser piece... Does anyone have ideas to brace or otherwise reinforce it to take the string tension? I attached a steel connector plate under the notched part to try to strengthen it but that obviously didn't help much.
what is it tuned to?
GDg

THENUGE said:
what is it tuned to?
hmmm...it must be a bunk piece i guess, i have only used poplar once, and i had it tuned to AEa for a while with no problems, though i added a maple fretboard. hope your next one is trouble free
Guess I should stop worrying so much about a problem with build#1 when I'm already gathering materials for build#2... and thinking about plans for #3... thanks for the input
Hmmm, I do use poplar and have had good luck. I make a laminated neck which greatly increases the strength. Else, I might put in a 1/8"x1/2" iron bar (lowes/HD) and that makes it solid.

I will agree tho that it does dent mar easy.

-WY

Duke T. said:
Poplar is not really a hardwood. Doesn't have enough rigidity for steel strings - might work with nylon, though. Best to stick with maple, walnut, oak, cherry, or hickory for necks - sometimes even mahogany 1 x 2 won't hold up under steel strings, but usually would work.
Absolutely! Your second (and third. and fourth. and fifth. and sixth....) will go MUCH smoother.

Oh and if its not fretted, I wouldn't worry too much about it.

-WY

Brian H said:
Guess I should stop worrying so much about a problem with build#1 when I'm already gathering materials for build#2... and thinking about plans for #3... thanks for the input

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

A.D.EKER commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Thank you Poorness ! for loving it ! appreciated!"
13 hours ago
Southern Ray replied to Timothy Hunter's discussion just came accross this pickup idea on youtube.
" Very interesting. Thank you Timothy!"
13 hours ago
Kent Thurston updated their profile
14 hours ago
Southern Ray posted a photo

Punch Project!

She now sports gold metal CBGitty knobs, speaker and an Artec 2.5 watt speaker. Finished this in…
15 hours ago
Southern Ray posted a photo

Project Punch!

Gonna finally get back on this long-delayed project that is more than half complete. (The matching…
15 hours ago
Poorness Studios liked A.D.EKER's video
17 hours ago
BrianQ. left a comment for Rob (Uker) Porras
"Hope this helps?"
17 hours ago
Doug Thorsvik commented on Doug Thorsvik's photo
Thumbnail

Dueling Flatheads

"I appreciate the kind words Papa D! I have always loved the look of these cigar boxes. Glad to have…"
20 hours ago
A.D.EKER commented on A.D.EKER's video
23 hours ago
A.D.EKER posted a video

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

The recorded History By Alan Lomax for the library of Congres of the Blues, from Mc Kinley Morganfield (Aka Muddy Waters) the in this take recorded Tribute ...
23 hours ago
Papa D commented on Doug Thorsvik's photo
Thumbnail

Dueling Flatheads

"Beautiful..Nice work Doug.."
yesterday
Papa D commented on Papa D's photo
Thumbnail

american1 Sun Glo

"Thanx AGP & Doug..  4 more coming soon"
yesterday

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->