I decided before Christmas I wanted to have a go at making my own magnetic pickups, and put it on my to-do list for the new year. I studied this guide http://www.instructables.com/id/Make-A-Guitar-Pickup/ extensively and ended up taking inspiration from a few other sources to come up with a design, here is the process:

I ordered a 500g spool of 42awg (0.063mm) copper magnet wire from Brocott's (UK supplier) and a couple of packs of alnico 5 rod magnets (5x19mm) on eBay. I had some 3mm sheets of sapele so I figured I would use this for the bobbins.

These were the first 2 bobbins I finished, I fixed the magnets flush with the top and bottom with a dab of superglue and drilled 2 holes for the start and end of the wire. It is really important to sand the inner surfaces of the bobbins completely smooth and free of any tiny burrs as the wire will get caught. Best case scenario you'll have to unwind several hundred turns, worse case the wire will break and you'll have to start over.

This is the winding jig I made. I did try a sewing machine first but I felt that I didn't have enough control. This is just a hand-cranked drill clamped to a desk, with a block of wood fixed to a dill bit. I attached the bobbin with an adhesive pad. One turn of the handle is about 4.2 turns of the bobbin, so I would do 50 turns, check for any tangle or loose winds, then do another 50 and mark a tally. When I had done 19 x 100 revolutions of the handle, I had roughly 8000 turns on the bobbin. This took about 30 minutes altogether.

I then decided to make a hole in the soundboard of one of my guitars to check for the fit. I use a neck-through design so I also needed to chisel out a recess for the bottom of the pickup to sit in.

I used a drill to start the hole, then fed a coping saw through to cut it out, then sanded etc. I then realised I hadn't thought of how to mount the pickup, and after looking at pages of pickups on Google images, I decided to start over and go for a top-mounting design. (Thanks to Mr. Crocker - an endless source of inspiration!)

These were mark 2. I made the tops of the bobbins larger than the bottom, so I could screw them into the soundboard through the top, covering up the hole for aesthetic and acoustic reasons. I also replaced the holes for the start and ends of the coil with small screws. I used steel screws for these but I do not recommend it - it is very tricky to solder onto them - as you can see:

Hmmm... not looking too great. Soldering was very difficult as I needed to melt off the enamel coating on the copper wire before the solder would stick. However I checked the connections by attaching a jack and plugging it in and it did work! Next step was potting.

This is a double boiler I constructed to melt the wax. I put about 600g of parrafin wax pellets into a kilner jar, placed a block of wood underneath so the jar was not in contact with the heat source and lashed the top of the jar to the sides of the pan with rubber bands. I filled with water up to about 1" from the top level of the wax and used a meat thermometer to gauge the temperature (which needs to be about 65c). I should add that I have an electric hob, and I think this process would be quite dangerous with an open flame. (This is so far the only advantage to an electric oven I have ever found).

Once the wax had all melted, I wrapped the lead wires from the pickup around a screwdriver and rested it on top of the jar, so the pickup was suspended in the middle, not touching the sides. The idea here is to wait until the bubbles stop rising and the coil will be saturated. I should add that the wood I used also took in wax - and bubbles came off that too. I have it about 20 minutes, took it out, wiped the excess from the bobbin and let it cool. I then wrapped round some PTFE plumbers' tape to protect the coil.

Then it was time to wire it up and put it in the guitar:

As you can see, I attached the pickup with 4 small screws. The clamps are there because I had to re-glue the lid on the box.

I then strung it up and plugged it in.

Hmm... not much volume, and lots of buzzing. I replaced the bridge with a pencil, to make it much lower, and the sound was louder - the pickup was too far from the strings. I also had not grounded the strings (which is a whole other problem as my bridge and tailpiece are both wood. Back to the drawing board again!

Pickup Vol Tone Jack

As you can see from Ted's diagram, the ground wire needs to connect the pot with the strings. I am planning to replace my wooden tailpiece with a metal one.

This is the new pickup I made last night. As you can see the top of the bobbin is much thicker, 6mm this time (an offcut from a sapele fretboard). The termination screws are now brass, so will be easier to solder. I also used a craft knife this time to scrape off the enamel coating, so soldering should be much easier. My next step is to pot it in wax and then wrap it with some copper foil tape, which just arrived yesterday. I will solder a wire from the ground on the pickup to the outside of the copper tape (thanks Bob Harrison for this tip). This combined with grounding the strings should have much better results, so fingers crossed.

I'll let you know how it goes!

Rick

[Part 2 here now: http://www.cigarboxnation.com/profiles/blogs/my-continued-adventure...]

Views: 1682

Comment

You need to be a member of Cigar Box Nation to add comments!

Join Cigar Box Nation

Comment by Blind Lemon Cello on March 3, 2019 at 9:03am
Comment by Richey Kay on February 23, 2014 at 7:40am
Yeah I thought about that Jabes. Would have been too messy on this guitar. My latest version has the string ferrules passing through a piece of copper tape and connecting that to the ground on the back of the pot. Did you spot your pup on this blog post? :-)
Comment by jabes on February 23, 2014 at 4:22am

rather than replacing your tailpiece could you not make a metal strip for the strings to pass through and earth that, with a wire soldered to it,? might save a bit of work.i did this on my 1st guitar and it worked fine .

j

Comment by t-belly johnson on January 10, 2014 at 6:44am

Nice work Richey

Comment by Richey Kay on January 9, 2014 at 1:11am

I should add that I haven't wound as many turns on the latest pickup. Somewhere in the region of 5000-5500. This is mainly due to having less space between the two bobbins. As this pickup will be going close to the neck, I think less winds would probably be better.

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

Doug Thorsvik commented on AGP #'s photo
Thumbnail

AGP #527 - ''Led-Zep 2''

"This build really strung you along Alan! Reminded me of all my fishing line experiments; a lot of…"
14 minutes ago
Doug Thorsvik commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Diggin’ the slow blues. I like that last pic Andries! Look at all those cool guitars. Yeah!!!"
19 minutes ago
Dar Stellabotta posted a video

A Cigar Box Guitar Six Stringer Built by Louie Lamanna

This video is the unboxing and the demonstration of a beautiful, six stringer built by Louie Lamanna. Join Louie and I June 15 at the second annual Pittsburg...
1 hour ago
Doug Thorsvik commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter to you too Andries! The passion is definitely in full swing. Turns out I’m…"
2 hours ago
A.D.EKER commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter Doug ! the Passion is in full swing !"
2 hours ago
A.D.EKER commented on Ricky D's photo
2 hours ago
A.D.EKER commented on A.D.EKER's video
2 hours ago
Keith Rearick liked Doug Thorsvik's video
6 hours ago
Keith Rearick liked A.D.EKER's video
6 hours ago
Keith Rearick liked Doug Thorsvik's video
6 hours ago
Keith Rearick liked Ricky D's photo
6 hours ago
Keith Rearick liked Ricky D's photo
6 hours ago

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->