I just completed construction a a Gitty license plate guitar. After I added the strings and started to adjust the strings, I noticed the action was so low that the strings are hitting the frets and giving a real tinny sound. I need to raise the action some. What is the best method of raising the action? 

  The open space under the license plate seems to be contributing as the bridge lowers as the strings tighten.

Views: 109

Replies to This Discussion

 Some of those license plates could be a little bendy, run a brace inside, across the body. 

First, do the internal bracing that BrianQ recommended.  If you still more clearance you can build up your bridge with a piece of hardwood as a foundation and or change the nut.

Hi rick, also check for high frets in buzzing area. A short straight edge over three frets and if rocking is evident you found a high fret.

Taff

Taff

i know they have fancy luthier ways of handling that fret.  Do you hit it with a file or is that not cool?

thanks

Hi Tim, well if you come across a high fret there are a few ways to remedy it, and it depends on what has caused the high fret.

it could have just lifted out of its slot, now filing it ain't going to fix that, it's still going to be out of its slot when you finish filing. So applying glue and holding the fret down until it sets is the way in this case. 

Sometimes the fret slot may not be deep enough and holds the fret up, in this case I'd say remove the fret and rework the slot.

Sometimes it can be up due to an uneven fingerboard or lack of good levelling when first installed, then I would use a file to level the fret with the others. One then has to recrown the fret and polish.

sometimes a Factory guitar can have less than perfect fretting.  These do not become evident until the customer asks for a low action, so a simple job can turn into a not so simple one. A complete fret dress.

When I get a new guitar in because of a high action I immediately think, why? Often times it's to hide the buzzing caused by clumsy fret installation.

Taff

Thank you Taff,

I see what you are saying in each case.  Thank you for that knowledge, I know that comes for years of experience and I appreciate it.

tim

Good advice from the guys above, and keep in mind you might have multiple issues in play. A "tinny" sound may actually just be the tone you're getting due to the metal soundboard. Check carefully to make sure the license plate isn't buzzing against the frame, and also check to see if a string slot on the nut or bridge is causing a buzz. I've seen that many times. If you're noticing movement as the strings tighten I would definitely consider a bit of bracing under the bridge. You don't want it to be completely rigid but it may need some added support.

Madgomer,

would the sound be better If the plate were connected in a rigid way to the  bracing (glue or screw)?

Or the contact between the plate and bracing have a flexible connection (rubbery glue or a rubber washer)?

Or would the bracing be ideal around the sides, leaving the plate/soundboard free to vibrate in the center, unencumbered?   

or a center post mounted from inside the box to the underside of the plate?

Or some other type of approach?

thank for your thoughts

tim

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Discussion Forum

Questions on a first time electric build.

Started by Michael shrader. Last reply by John Mark Perchalski 22 hours ago. 4 Replies

Questions about CBG details...

Started by James Pobog. Last reply by James Pobog Dec 13, 2019. 8 Replies

Magnetic Pickups - What's good

Started by Jim Codog. Last reply by Jim Codog Dec 12, 2019. 7 Replies

Yardstick Fretboards

Started by Jim Codog. Last reply by Jim Codog Dec 11, 2019. 6 Replies

General wiring question

Started by James Pobog. Last reply by James Pobog Dec 9, 2019. 5 Replies

Soldering/grounding plan

Started by T-Gripped. Last reply by Gus K Dec 7, 2019. 7 Replies

I'm gonna need help...

Started by James Pobog. Last reply by MadGomer Dec 6, 2019. 4 Replies

Building my first CBG....

Started by James Pobog. Last reply by James Pobog Dec 4, 2019. 6 Replies

About neck thru....

Started by James Pobog. Last reply by John Mark Perchalski Dec 4, 2019. 1 Reply

Fitting Frets

Started by neddy. Last reply by Taffy Evans Nov 27, 2019. 8 Replies

Joinery suggestions for hand-made boxes

Started by Chris Wharton. Last reply by MadGomer Nov 23, 2019. 43 Replies

Fretted....

Started by Jim Codog. Last reply by Jim Codog Nov 20, 2019. 5 Replies

Connecting a guitar jack?

Started by rick schoen. Last reply by David Clewell Nov 17, 2019. 5 Replies

Fretting for beginners

Started by Michael Myers. Last reply by MadGomer Nov 14, 2019. 3 Replies

Adjusting the action on a cbg 3 string.

Started by rick schoen. Last reply by Tim Pannabecker Nov 11, 2019. 8 Replies

Tuner and nut question.

Started by Bill. Last reply by Gus K Nov 6, 2019. 12 Replies

Help with first tuning procedure.

Started by James Pobog. Last reply by Mark Bliss Nov 6, 2019. 3 Replies

Too far gone??

Started by T-Gripped. Last reply by Mark Bliss Nov 6, 2019. 7 Replies

Pickup query

Started by Arthur Payne. Last reply by Arthur Payne Nov 6, 2019. 11 Replies

Blog Posts

New Member need a little advice.

Posted by Don Paul on January 26, 2020 at 10:29am 5 Comments

Neck bowing

Posted by Mike Kinzie on January 24, 2020 at 5:38pm 2 Comments

Dual lap steel

Posted by Ron Lutz on January 9, 2020 at 2:42pm 4 Comments

My 3 Gitty Kits

Posted by Poorness Studios on January 8, 2020 at 9:20am 2 Comments

My CBG details

Posted by Paul scofield on January 1, 2020 at 9:22am 2 Comments

Latest Activity

Dave Lynas posted a photo
3 minutes ago
Dave Lynas posted a photo

Minnesota Girl

On my bench. Gitty Custom print Box Guitar. Slow progress but looking good. Ben did a great job…
4 minutes ago
Dave Lynas commented on Dave Lynas's video
13 minutes ago
Dennis "Denbo" Goodinson liked Shane Speal shanespeal.com's video
1 hour ago
KOOL DOG HOOCH replied to KOOL DOG HOOCH's discussion In memory Hooch!
"Thanks Taff and Pick for the kind words, I've had dogs my whole life and everyone of them was…"
1 hour ago
Blind Boy Fullers liked BUGGY (C)'s video
2 hours ago
Profile IconJames A Fowler, Anna LaRue, Carla Proud and 3 more joined Cigar Box Nation
3 hours ago
Randy S. Bretz posted a photo

Purpleheart surround for a Black Mamba

Just another part I made from Purpleheart for the cherry 1 piecer
3 hours ago
Jerry Jordan commented on AGP #'s photo
Thumbnail

AGP #376 - ''Dave''

"Great job.,very nice.,"
3 hours ago
Jerry Jordan commented on Tim W's photo
Thumbnail

111554FE-C45C-4E39-8551-62C1DD939B35

"So you want to level the frets,.?"
3 hours ago
Brent Kasl replied to Brent Kasl's discussion Correcting a back bowed neck
"Thanks"
4 hours ago
Jerry Jordan commented on Nick Cardenez's photo
Thumbnail

Double box hot fox

"You appear to be having too much fun,,, excellent execution "
4 hours ago

Music

Loading…

© 2020   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->