Haven't started yet, but I'm reviewing the instructions from the kit (the full one with fretted neck) an I saw the neck gets a relief cutout for the box lid. But....the box  got does not have a recessed lid. That means I skip that step, right? I will prolly be adding a pickup, but at that point I'm just cutting a dado and re-enforcing the neck under the cut, right?

Views: 67

Replies to This Discussion

I haven't used the kit, you'll want to think about the fit and how much clearance you'll have for your fretboard. Remember that the action (the distance between the strings and the frets) becomes quite important, so consider that geometry. Will your fretboard lay so that it's surface is above the cigar box's lid? Think about where it'd be if the lid WAS inset, then where it's going to be based on your box. THink about how that's going to affect the geometry of your bridge based on its height relevant to your nut. Adjust as necessary.

Adjust as necessary is kind of THE advice when it comes to CBGs. I do apologize if that's not helpful.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Discussion Forum

Questions on a first time electric build.

Started by Michael shrader. Last reply by John Mark Perchalski yesterday. 4 Replies

Questions about CBG details...

Started by James Pobog. Last reply by James Pobog Dec 13, 2019. 8 Replies

Magnetic Pickups - What's good

Started by Jim Codog. Last reply by Jim Codog Dec 12, 2019. 7 Replies

Yardstick Fretboards

Started by Jim Codog. Last reply by Jim Codog Dec 11, 2019. 6 Replies

General wiring question

Started by James Pobog. Last reply by James Pobog Dec 9, 2019. 5 Replies

Soldering/grounding plan

Started by T-Gripped. Last reply by Gus K Dec 7, 2019. 7 Replies

I'm gonna need help...

Started by James Pobog. Last reply by MadGomer Dec 6, 2019. 4 Replies

Building my first CBG....

Started by James Pobog. Last reply by James Pobog Dec 4, 2019. 6 Replies

About neck thru....

Started by James Pobog. Last reply by John Mark Perchalski Dec 4, 2019. 1 Reply

Fitting Frets

Started by neddy. Last reply by Taffy Evans Nov 27, 2019. 8 Replies

Joinery suggestions for hand-made boxes

Started by Chris Wharton. Last reply by MadGomer Nov 23, 2019. 43 Replies

Fretted....

Started by Jim Codog. Last reply by Jim Codog Nov 20, 2019. 5 Replies

Connecting a guitar jack?

Started by rick schoen. Last reply by David Clewell Nov 17, 2019. 5 Replies

Fretting for beginners

Started by Michael Myers. Last reply by MadGomer Nov 14, 2019. 3 Replies

Adjusting the action on a cbg 3 string.

Started by rick schoen. Last reply by Tim Pannabecker Nov 11, 2019. 8 Replies

Tuner and nut question.

Started by Bill. Last reply by Gus K Nov 6, 2019. 12 Replies

Help with first tuning procedure.

Started by James Pobog. Last reply by Mark Bliss Nov 6, 2019. 3 Replies

Too far gone??

Started by T-Gripped. Last reply by Mark Bliss Nov 6, 2019. 7 Replies

Pickup query

Started by Arthur Payne. Last reply by Arthur Payne Nov 6, 2019. 11 Replies

Blog Posts

New Member need a little advice.

Posted by Don Paul on January 26, 2020 at 10:29am 5 Comments

Neck bowing

Posted by Mike Kinzie on January 24, 2020 at 5:38pm 2 Comments

Dual lap steel

Posted by Ron Lutz on January 9, 2020 at 2:42pm 4 Comments

My 3 Gitty Kits

Posted by Poorness Studios on January 8, 2020 at 9:20am 2 Comments

My CBG details

Posted by Paul scofield on January 1, 2020 at 9:22am 2 Comments

Latest Activity

Randy S. Bretz posted photos
39 seconds ago
KOOL DOG HOOCH replied to Tim W's discussion One finger Barre cord technique
"I use a dime on 1st fret and a quater on 12 to start out and it puts me in the ballpark."
1 hour ago
Dave Lynas posted photos
1 hour ago
Uncle John commented on AGP #'s photo
1 hour ago
Uncle John commented on Dave Lynas's photo
1 hour ago
Dave Lynas liked Tim W's photo
1 hour ago
Dave Lynas commented on Tim W's photo
Thumbnail

111554FE-C45C-4E39-8551-62C1DD939B35

"String height at the base of the neck is often a bit high for slide play. I have a low action at…"
1 hour ago
Dave Lynas liked AGP #'s photo
1 hour ago
Dave Lynas liked AGP #'s photo
2 hours ago
Dave Lynas liked AGP #'s photo
2 hours ago
Dave Lynas commented on AGP #'s photo
Thumbnail

AGP #376 - ''Dave''

"Looking Great AGP. BET SHE SOUNDS great as well! Thanks for this namesake build ! I’ll love…"
2 hours ago
Dave Lynas commented on Dave Lynas's video
2 hours ago

Music

Loading…

© 2020   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->