I've just finished a CBG with 2 mini humbuckers. The neck pup is much louder than the bridge pup. The neck pup measures 6.7K and the bridge pup measures 7.5K. I wired with a master volume/master tone so after the selector switch both pups share the same circuit so it's not a pot or the jack connections. I'm no electronics expert but my understanding is the higher the impedance the "hotter" (louder) the pup is. Am I wrong? Any suggestions?

Views: 304

Replies to This Discussion

Neck pups are generally louder because the strings are moving/vibrating much more nearer the middle of the string. Most people ballance the volume from the controls but you can also lower the pup down so that the strings are further away from it. This would drop the volume. You could reverse this and bring the other pup up closer to the strings.

Solid info and advice again Fomhorach. I'm yet to encounter this issue but I'm also yet to put more than one pickup on a build. Your info will prepare and help me too. Thanks muchly! 

Thanks for the response Fomhorach. What you say makes perfect sense but I think in this case it's more than that. I'm well aware that the neck pickup gets more vibration which is why I put the supposedly "hotter" pickup in the bridge position. I also set the bridge pup much closer to the strings. It's about .1" away from the strings while the neck pup is .2" away. Still the neck pup is much louder. I can't balance them with the control because they share a master volume.

There's other things to consider too. If one is drowning out the other, or making eq unbalanced check that you have used both pickups live out because reversing the pickup can cause frequency cancellation. Try reversing one of them as well. Not the wires but the whole thing just flip the left to the right.

After that I can't think of any more quick tricks.

Some electrical oddness can be fixed by the use of diodes (I think it's diodes, someone jump in here with the right way this is done)
Inserting a diode limits the signal direction to stop cross chatter between pickups on the one circuit.

Yes, I would suggest the same thing as an easy fix. Adjust the height of the pickups up or down until you get the loudness balance you want. 

There are some other things that can affect loudness such as the strength of the magnets, and number of winds, but it's easier not to mess with that. 

Could also be a pickup with a weak magnet or defective coil. If pickup height doesn't help and it's wired properly, you need to return it for a replacement.

Is it a 2 wire or 4 wire pickup? Can you take some pics of your wiring?

Sorry, computer problems have kept me offline for a week. I lowered the neck pickup to almost .3" from the strings and left the bridge pickup .1" from the strings and the balance is now pretty good. I love the sound of these pickups but I do think the bridge pickup is a little weak and I have to turn my amp up a bit more than usual. Thanks to all who replied, there are a lot of knowledgeable people in the nation. 

no=one has mentioned it but isn't 3" rather a long way from the strings ? I'd have thought 1/4 to 3/8 a bit more the norm ...

Sorry jabes but I just saw your reply. The measurement isn't 3" but rather 0.3" which is 300 thousandths of an inch which IS between 1/4 and 3/8.

It's not uncommon to have to lower the neck pickup that far down, especially if the 2 pickups are close to each other in output. I have a few that are that way.
I have found that I like the neck pickup to be around 8K to 9K resistance for a neck Humbucker and 11K to 12K resistance for a bridge Humbucker. So it's good to have around 2K more output in the bridge pickup for double coil/humbuckers and 1K to 2K for single coil bridge pickups.
Another thing could be the type of magnets. There's (Alinco 2, 3, 4, 5 and 8), there's a few different strength Ceramic magnets and there's Neodymium magnets. Magnets can make a difference in how a pickup performs. Sometimes the guitar responds to one type better than another. Some people like a mix of pickups like a ceramic in the neck and a Alnico in the bridge. Lots of the cheaper pickups have Ceramic magnets in them, so changing to another type or stronger magnet can be a big change.

RSS

The Essential Pages

New to Cigar Box Nation?How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

 

Recommended Links & Resources

Discussion Forum

Wiring CB Gitty Black Ice Single Coil

Started by ILL GREEN. Last reply by ILL GREEN Jan 9. 5 Replies

Minimal effect from volume or tone pot

Started by Arthur Payne. Last reply by Paul Craig Dec 21, 2018. 9 Replies

Problem posting discussion

Started by Arthur Payne. Last reply by Paul Craig Dec 17, 2018. 2 Replies

Creackle from Volume and Tone pots

Started by Arthur Payne. Last reply by Arthur Payne Nov 27, 2018. 3 Replies

Vol, tone, 3 way toggle and 2 single coils?

Started by Slow Blues Dani & Ol' Grey Bear. Last reply by Paul Craig Nov 25, 2018. 20 Replies

Output method

Started by Holly Hodson. Last reply by Holly Hodson Oct 23, 2017. 2 Replies

two picksups - both or separate

Started by Reynhard Boegl. Last reply by Reynhard Boegl Sep 27, 2017. 8 Replies

Psycho knob

Started by bizzaro guitaro. Last reply by bizzaro guitaro Sep 19, 2017. 4 Replies

Psycho knob install

Started by bizzaro guitaro. Last reply by bizzaro guitaro Sep 19, 2017. 13 Replies

Psycho knob

Started by bizzaro guitaro Sep 18, 2017. 0 Replies

I cheated and bought a solderless wiring harness. Naughty boy!

Started by Slow Blues Dani & Ol' Grey Bear. Last reply by Slow Blues Dani & Ol' Grey Bear Aug 18, 2017. 46 Replies

Capacitor

Started by Rose Ericson. Last reply by Rose Ericson Jul 8, 2017. 2 Replies

Wiring A Dual Rail Pickup into A Cbg

Started by Philip Hale. Last reply by Paul Craig Jun 2, 2017. 5 Replies

Buzz or maybe humm

Started by Rose Ericson. Last reply by Paul Craig Mar 12, 2017. 8 Replies

unbalanced pickups

Started by Don Tucker. Last reply by Paul Craig Dec 30, 2016. 13 Replies

Guitar Tone Capacitor Shootout

Started by Scott aka Farmer Ted. Last reply by Wayfinder Nov 22, 2016. 6 Replies

Wiring

Started by Philip Hale. Last reply by sasquatcher Nov 20, 2016. 6 Replies

Capacitor wiring for CBG with Piezo and Volume control.

Started by Ray Peltzman. Last reply by Ray Peltzman Oct 11, 2016. 5 Replies

Six pole pickup on a three string guitar.

Started by Slow Blues Dani & Ol' Grey Bear. Last reply by Wayfinder Sep 13, 2016. 40 Replies

Latest Activity

Uncle John commented on Andries D. EKER's video
Thumbnail

Come on Down to Calli Fest BCB One man Band 2019

"I like that echoing sound.   Good one, A.D.  I don't know what Richard has…"
53 minutes ago
Taffy Evans replied to Ducati Scotty's discussion Fret press anyone?
"Hi Jerry, If I may offer a bit of advice re tapping frets in, keep the word "tapping" in…"
54 minutes ago
Uncle John commented on BUGGY (C)'s video
Thumbnail

The fun is over !

"Ominous and spacy too.  Well done, but skeery.  A pupped dog bit me when I was a…"
56 minutes ago
Uncle John commented on Uncle John's video
Thumbnail

Cali Fest ~ Hank Williams Open Mic sign up

"Doc Blues, I know the song you are talking about.  Got you on the list. Thanks! Thanks brother…"
59 minutes ago
Korrigan commented on Korrigan's video
Thumbnail

Build #28, Isadora

"Thanks Jason!"
1 hour ago
Paul Craig liked Mike Willmouth's video
1 hour ago
Paul Craig commented on BeetleJuice!'s blog post Fender Plans a USA made Acoustic
"I saw a video on this guitar being demo'd by a guitarist. It sounds very good as a Acoustic…"
1 hour ago
Denny liked Jérôme B's video
2 hours ago
BrianQ. commented on BUGGY (C)'s video
2 hours ago
gordon barnes posted a blog post

pentatonic scale fret board or neck

Anybody know where I can buy a pentatonic scale fret board or fretted neck?See More
2 hours ago
BrianQ. liked BUGGY (C)'s video
2 hours ago
BrianQ. liked Uncle John's video
2 hours ago

Music

Loading…

© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://api.ning.com/files/Stym6V-ACBaiDP5ilIPA6bJ3rn0ZdlI1EwGHWgROvEkwiCCaNgzJRcZTZH8OGkV3fvK-NboXjThXltWFbcihM-jI4Mwz5SV3/scrollup_icon.png") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->