I am new to CBG building. I have built 2 so far and I have used 5/16 bolts for the nut and bridge. I recently bought two laser-cut wooden bridges and two bone nut blanks. My question is: the wood bridge is considerably higher than the 5/16 bolt. Does anybody else use these and do you cut them down in size? Also, are there any special techniques I should use installing the bone nuts? Thanks for any suggestions/solutions.

Views: 242

Replies to This Discussion

Hi Lou - I build with both a bone nut and a shaped oak bridge. The height of the bridge and nut will determine the action - the height of the strings above the fret board - and frankly it's a repetitive process for me of sanding down the bridge and grooving the nut until the action is where I want it. (This is where one of the battery operated power winders comes in handy.) The bridge I sand down the bottom to reduce the height. The top of the bridge I put a bit of a peak on it and leave it floating. The nut however, I do not sand down the bottom. It is nice and flush already and that I leave. I file in the grooves for the strings and keep filing the depth of the groove until I get the action I want. Then I file down the top of the bone nut until it is just above the bottom of the grove (professional standards will say the top of the nut should leave about half of the diameter of exposed string above the top of the nut). I have experienced if the bone nut is not filed properly on the takeoff towards the tuners (you'll want to round this down a bit), you may get string buzz. I usually find my buzz goes away by either filing the grove on the takeoff towards the tuners, or cleaning up the groove in the nut. There is plenty of info here and also on the net on filing grooves for bone nuts. After the first few, you'll be a pro at it. ;-) P.S. I did all my grooves without any fancy files for most of first builds and they play just fine. Hope this helps - any more questions - ask away.

Thanks for the feedback, Joe. I am building it fretless, so the string height is not super critical, but I would like to keep it around 5/16". I'll be sanding away! Thanks again.

Hi Lou - further to my note (for some reason I can't seem to edit my note) - there is also plenty of info on Youtube on this subject, and how to check for proper action.

It sounds like an acoustic; are you planning on ever adding a piezo and input jack so it can be plugged into a amp? I believe under the bridge is a good place for a rod piezo, especially if your soundboard is small and you don't get a good sound from the piezo on the soundboard, and/or you have other space constraints in the interior. Maybe it's possible to embed a rod piezo into the top of the bridge? I don't know, but I am so excited about the possibilities that I'm going to install one in a cheapo ukulele, just to see if it works. A pickup also could save a "failed" build, so I'm taking this into consideration for all my future builds.

Actually it's cheap enough to buy finished bone nuts, so I haven't tried to notch my own. Also, I'm assuming you're aware that usually notches are made in proportional size to the strings. This may be overkill on a CBG, no doubt you noticed the bolt works fine. Although if you want to make it convertible to string left or right handed, you might avoid gluing the nut.

I installed the pre-amp bundle from CB Gitty that comes with the rod piezo. The rod is directly under the bridge and I think it sounds great. The bone nut took a little time and effort to get it to my liking, but I am satisfied with it. The Patron box makes a beautiful guitar. Thanks for your input.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Discussion Forum

Rough scarf joint seam

Started by Michael shrader. Last reply by BrianQ. yesterday. 4 Replies

Is EBE tuning more tension or less?

Started by Warren Williams. Last reply by BrianQ. yesterday. 2 Replies

Fret sizes.

Started by neddy. Last reply by neddy on Friday. 13 Replies

Too far gone??

Started by T-Gripped. Last reply by Tim Pannabecker Oct 15. 6 Replies

Scarf joint headstock

Started by Lou Ellis. Last reply by Taffy Evans Oct 9. 5 Replies

Help with first tuning procedure.

Started by James Pobog. Last reply by James Pobog Oct 4. 2 Replies

2 string cbg

Started by Dickie. Last reply by BrianQ. Sep 1. 5 Replies

A simple tuning peg question

Started by Warren Williams. Last reply by MadGomer Aug 26. 6 Replies

How could this be?

Started by stephen davies. Last reply by stephen davies Jul 9. 2 Replies

Grounding

Started by Robert M J Loftus. Last reply by stephen davies Jun 30. 6 Replies

Pickup Placement on High G Ukulele

Started by Chris Sturhann. Last reply by Chris Sturhann Jun 19. 2 Replies

Shipping

Started by Virginia Bill. Last reply by Jim Brown Jun 12. 4 Replies

Neck Bowing?

Started by Craig Cole. Last reply by Craig Cole Jun 11. 11 Replies

Springs in an acoustic cbg

Started by Will "KOOL DOG HOOCH" Bonner. Last reply by Will "KOOL DOG HOOCH" Bonner Jun 1. 8 Replies

Weird Little Install Issue

Started by Craig Cole. Last reply by Craig Cole Jun 1. 5 Replies

CBGitty Amp kit

Started by Art Prior. Last reply by Paul Craig May 31. 4 Replies

Earthing Strings

Started by mitch jones. Last reply by mitch jones May 18. 7 Replies

Like a box of chocolates

Started by Michael shrader. Last reply by Michael shrader May 11. 3 Replies

Intonation problem

Started by Ramson. Last reply by Will "KOOL DOG HOOCH" Bonner May 3. 14 Replies

Pure and simple CBG

Started by Bill McNamara. Last reply by Craig Cole Apr 30. 6 Replies

Blog Posts

Tab for Ry Cooder

Posted by Keith Gibson on September 30, 2019 at 12:44pm 2 Comments

Ducktail Run in James Dean Country

Posted by Rick Tish on September 29, 2019 at 9:57pm 1 Comment

Tiki mask guitar

Posted by Phil Stickings on September 27, 2019 at 12:39pm 5 Comments

Festival in the land that time forgot

Posted by Rick Tish on September 23, 2019 at 10:09am 2 Comments

Latest Activity

V. Wiswell is now a member of Cigar Box Nation
48 minutes ago
Randy S. Bretz liked AGP #'s photo
55 minutes ago
Randy S. Bretz posted photos
2 hours ago
Shane Sylvester commented on JP Swenson's photo
Thumbnail

Nail Pick-up - Single- Didley Bow

"have you got a small neo magnet on that"
3 hours ago
Dave Lynas commented on Dave Lynas's video
Thumbnail

Cheroots the Bear

"Thanks guys. Using these minis as basses is my surprise discovery. I like the ukulele basses but…"
3 hours ago
Rich Butters replied to Rich Butters's discussion Cigar Box Dimentions and Wood Thickness
"Hi Blue Rat,  Thank you for the message and the advice.  This is the dimensions of the…"
6 hours ago
Paul Craig liked Adam Cripps's video
6 hours ago
Paul Craig liked Dave Lynas's video
6 hours ago
Paul Craig liked Vinsanity's discussion Shovel Handle Diddley Box
6 hours ago
Paul Craig replied to Taffy Evans's discussion Video.. Building an Evans full acoustic guitar
"Love the headstock inlay and the whole guitar looks great."
6 hours ago
Paul Craig liked Taffy Evans's discussion Video.. Building an Evans full acoustic guitar
6 hours ago
Paul Craig replied to JP Lace Master's discussion Collection Thread: show me your collections
"I like the sound holes on the middle CBG."
6 hours ago

Music

Loading…

© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->