Just curious what kind of tools used to shape necks. I've been using router, rasp, sandpaper. I like old hand tools. and have been looking at draw knives and spokeshaves. Not very familiar with them, never used either. Anyone use them. Lots of old ones on eBay, but lack of knowledge keeps me from buying.

Views: 957

Reply to This

Replies to This Discussion

Spoke shave, rasp, files and sandpaper to make a traditional guitar neck profile. I used a reciprocating saw (sawsall) for lack of a bandsaw and a coping saw for shaping the peghead. I have used the router and roundover bit for a flatneck and a hand plane on a closet rod for a different shape. I use a radius sanding block with progressively fine sandpaper for fingerboard radiusing.
I need a new blade for my coping saw. It is bowed. It is amazing how much you can accomplish with a simple coping saw. I use the coping saw for the first cut.

I hit the neck with the sanding drum in the air die grinder to shape it, but finished it with a half round bastard file, then sanding paper.

The Air Die Grinder is just for clean up after shaping with the coping saw.
I use a spokeshave to do the basic shaping of the back of the neck and then successive grades of abrasive paper (80, 180, 240 and finally 400 to finish). I have a small electric sander (which was described as a "detail sander"), but mostly I do the sanding by hand.

For cutting out substantial sections (eg. for the headstock or for pickup recesses) I use one of a variety of saws, followed usually by a bit of work with a coarse file. Then, once more, it's abrasive paper to finish.

I guess the timber you use will affect how easy or how well various tools and techniques will work out. I've been using sapele (because it was easy to get small pieces from local joinery firms). It seems to be a very easy wood to work while also being very strong and I've found the spokeshave and other handtools to be all I need with this material.
Thanks. I thought my cheap HF spokeshave was junk until I bought a better sharpening stone and lowered the angle of the spokeshave and set it so that the blade was barely sticking out of the surface. Works great now.

Don Miller said:
Rasp and file to shape the ends of the neck, then spokeshave to connect them. Scrapers to get rid of spokeshave and rasp marks, and 220 grit to make it smooth and ready for finish.

Wade, I find that some chunks of wood don't like to be shaved one direction, even with a sharp spokeshave making a very light cut. If I start to get chatter and chunks, I can usually just go the other way.
Another method i use for sanding, I use a strip torn off a sheet of sanding paper. I stick clear packing tape on the back of the strip. Last real long with out tearing.
using alcohol accomplishes the same thing but does not add moisture to the wood.

Mark Werner said:
A trick I learned from bow-making... (might be common knowledge...) When you get down to the final finishing with ultra-fine sandpaper, wet the wood with a damp cloth.
This will raise the grain; you'll be amazed at how rough your previously-smooth piece feels.

Go over that with very fine (300-400) sandpaper and you'll have a nice, smooth finish that won't raise any more when you apply finish.
That is a great idea, I am constantly breaking the sandpaper and that will help alot---thanks

Paul Doug said:
Another method i use for sanding, I use a strip torn off a sheet of sanding paper. I stick clear packing tape on the back of the strip. Last real long with out tearing.
Mike Patterson said:
That is a great idea, I am constantly breaking the sandpaper and that will help alot---thanks

Paul Doug said:
Another method i use for sanding, I use a strip torn off a sheet of sanding paper. I stick clear packing tape on the back of the strip. Last real long with out tearing.

Even better, I have started using Klingspor's sandpaper. Buy in rolls, cloth backed. A roll will last me for a very vewry long time.

http://www.woodworkingshop.com/cgi-bin/A6B13374/mac/additmdtl.mac/s...
I use an old drawknife, spokeshave and rasps before it gets the sandpaper treatment. Once you use a drawknife and get the knack of using one you'll wonder why you didn't use one before. I use it for shaping just about anything wooden...from necks to carved wooden spoons! Trick is to keep'em sharp and you can do wonders.
In an earlier post back in June I believe, I said that I use handtools to get the final shape.Thats no longer true except for hand sanders.
Now after I cut out the basic shape with the bandsaw,It goes to the table belt sander. There I get the shape very close to final sanding ready using rough belt paper.
Then I switch to smooth belt paper to get closer to the shape. Then the neck goes to the workbench and I spend a few minutes with 60 grit on a handsander to get it to the point where its almost ready to stain.
I grab another sander thats preloaded with the final smooth grit and get that final look I want.I tend to attack the neck moving the sander so fast that sometimes my hand is a blur.
I cut a hole in the other end ( I cut all my necks slightly long) so I can hang the necks upside down for drying.
So I have found that the less handtools used ( for me) not counting hand sanders , the faster I can get that necks painted or whatever its getting.
I do neck sessions where I'll take as many as 6 to 8 necks from log form to ready to paint necks in a couple of hours.Few breaks, as I hate to lose my momentum when I'm in a session.I build my necks during the week , before and after my real job. Fri-Tues. Wed and thurs I assemble all the parts I've been working on all week. By Fri I'm ready to haul all the stock to my retail shop and hopefully swap em for money.
During the season I will build as many as 8-10 3 stringers and 4 to 10 1 stringers .All built using as many methods as I can to avoid as much handwork as possible.
It works great for me,I dont see any way I could get as many pieces done if I used as much handwork as I used to.I'm exploring ways to cut more handwork down so I can get the higher numbers built and ready during the heavy part of the season here.One thing I'm looking at is a longer table sander to make it possible to sand more of a neck at a time cutting even more time.
http://www.hobbylinc.com/htm/xac/xacx75300.htm
http://www.hobbylinc.com/htm/xac/xacx75330.htm

these are perfect for cutting fret slots in 1.5 in (1*2)s and it's CHEAP!

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

A.D.EKER commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Thank you Poorness ! for loving it ! appreciated!"
11 hours ago
Southern Ray replied to Timothy Hunter's discussion just came accross this pickup idea on youtube.
" Very interesting. Thank you Timothy!"
11 hours ago
Kent Thurston updated their profile
12 hours ago
Southern Ray posted a photo

Punch Project!

She now sports gold metal CBGitty knobs, speaker and an Artec 2.5 watt speaker. Finished this in…
13 hours ago
Southern Ray posted a photo

Project Punch!

Gonna finally get back on this long-delayed project that is more than half complete. (The matching…
13 hours ago
Poorness Studios liked A.D.EKER's video
15 hours ago
BrianQ. left a comment for Rob (Uker) Porras
"Hope this helps?"
15 hours ago
Doug Thorsvik commented on Doug Thorsvik's photo
Thumbnail

Dueling Flatheads

"I appreciate the kind words Papa D! I have always loved the look of these cigar boxes. Glad to have…"
18 hours ago
A.D.EKER commented on A.D.EKER's video
21 hours ago
A.D.EKER posted a video

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

The recorded History By Alan Lomax for the library of Congres of the Blues, from Mc Kinley Morganfield (Aka Muddy Waters) the in this take recorded Tribute ...
21 hours ago
Papa D commented on Doug Thorsvik's photo
Thumbnail

Dueling Flatheads

"Beautiful..Nice work Doug.."
yesterday
Papa D commented on Papa D's photo
Thumbnail

american1 Sun Glo

"Thanx AGP & Doug..  4 more coming soon"
yesterday

Events

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->