Hi folks,

I'm creating a 5-string out of an olive oil can and a poplar 1x3:

At first, I was thinking of doing a simple neck-thru design, like I would with a standard CBG, with a cutout in the neck for the body, elevating just a bit above the can surface. The can would be glued or screwed to the neck:

It occurs to me, however, that I'd get much less of a banjo sound this way, as opposed to a variant where the neck-thru portion didn't directly contact the top of the body. Given that I don't have much neck depth to work with, what's a good option for this? Could I just thin out the area under the bridge?

Please bear in mind that I have a limited selection of handtools, no shop space beyond my small Brooklyn living room, and precious little woodworking skills! I'm totally experimenting here.

I'm hoping to end up with something similar to Flatfoot Johnny's Golden Syrup canjo. Any advice is greatly appreciated.

Views: 1447

Replies to This Discussion

You might want to add (glue on) a thin strip of wood to the under-side of the neck where it goes through the can to compensate for the wood you remove on the upper-side so the "sound board" side of the olive oil can. The gap between the neck and the "soundboard" doesn't have to be more than 1/4", so it shouldn't weaken the poplar neck very much should you decide not to reinforce the under-side of the neck-thru.

As another pointer, you may want to tilt the neck downward by a couple degrees so the strings coming off the neck will rise up (a bit higher clearance) off the sound board to meet the bridge. You can trim off a triangular cross section of the tail end of the neck to allow you to mount it a bit higher to achieve the slight downward angle of the neck. Let me draw a diagram...Hope this helps...

-Rand.

Thanks for the reply, Rand! I think I'll have enough wood left over on the end to fashion a little wedge and give the action a boost. 

One question: in a design like what you illustrated above, what's actually holding the neck in place? is it just string tension?

Hi Noam,

Sorry for not getting back to you sooner. The CBN discussion group called the Canjo Consortium has at least one discussion about how people attach a neck to a cookie/cake tin. Here is the link I was thinking of.

The neck needs to be held in place typically by a couple of wood screws strategically located around the two places where the neck intersects to cookie/cake tin. When cutting the one (or two) hole(s) for the neck, cut the metal using an "X" cut and bend the 4 triangular metal "tabs" back into the tin. You can use one or two of these tabs to secure the neck to the tin by drilling a hole in the middle of the tab and then use a wood screw (or 2) to hold the tin in place. You'll be fastening the wood screw(s) into the neck. You can do this twice for a true "neck-thru", ore just once for what I call a "neck-almost-thru" design. In this later design, the end of the neck does not penetrate the can, but usually a couple of wood screws are used to hold the tin to the end of the neck. It helps if the end of the tin is rounded to conform with the inner surface of the tin. Since the junction at both these "points" are the weak points, most builders try to reinforce the sides of the tin with a wooden collar to help spread the load so the tin has a better chance of surviving rough handling. But the string tension itself should be fully handled by the neck. This means you want to either use the tail end of the neck as your tail piece, or in the case of "neck-almost-thru" designs, firmly secure your neck piece by fastening it into the end of the neck. Other builders may use different attachment techniques, so a bit research and experimentation should go a long way. Hope this helps.

-Rand.

RSS

The Essential Pages

New to Cigar Box Nation?How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Discussion Forum

Tambourine banjo. Skin bending pretty much.

Started by Sebastian Mueller. Last reply by Sebastian Mueller Sep 15. 1 Reply

not technicaly a banjo, but banjo-ish

Started by Iain T.S.. Last reply by turtlehead Aug 23, 2016. 1 Reply

Laser cut bridges cbgitty

Started by egyptpunk Aug 4, 2016. 0 Replies

Large book with banjo plans

Started by Wade. Last reply by Jim Morris Mar 12, 2016. 4 Replies

Tin can banjo: Neck-thru options?

Started by Noam Berg. Last reply by Rand Moore Apr 4, 2014. 3 Replies

Building Round Sound Boxes for Banjos

Started by Rand Moore. Last reply by Rand Moore Nov 6, 2013. 5 Replies

Some specifically general questions

Started by Matt Quinney. Last reply by Rand Moore Oct 11, 2013. 33 Replies

4 string banjo strings

Started by Mr. Toad Oct 1, 2013. 0 Replies

4 string or 5 string banjo for blues?

Started by JIm Trussler. Last reply by Gerald Readore Aug 22, 2012. 1 Reply

5-String Banjo Discussion Area

Started by Rand Moore. Last reply by Ryan Rose Feb 4, 2012. 10 Replies

a free banjo album, sort of

Started by Matthew Borczon. Last reply by Matthew Borczon Jan 15, 2012. 2 Replies

Banjo Blues Tab

Started by Gary Davis. Last reply by Matthew Borczon Jan 12, 2012. 5 Replies

CB Banjuke Project

Started by John Hopper. Last reply by Rand Moore Dec 1, 2011. 1 Reply

Banjo Ukulele

Started by John Hopper. Last reply by Rand Moore Nov 27, 2011. 4 Replies

Need help identifying a banjo

Started by DonnieC. Last reply by Mark Bliss Sep 28, 2011. 1 Reply

General Questions

Started by Kyle. Last reply by Mark Bliss Sep 4, 2011. 3 Replies

Blog Posts

3. German CBG Festival

Posted by Markus Gaiser on September 16, 2018 at 3:42pm 1 Comment

..absolute authenticity!

Posted by billy jones bluez on August 18, 2018 at 10:30pm 0 Comments

Other woodwork

Posted by Tom E on August 16, 2018 at 5:00pm 4 Comments

kannel/ kantele (Baltic psaltery)

Posted by Tom E on August 16, 2018 at 1:00pm 4 Comments

Latest Activity

Wade posted a photo

Aged Nickel Pickup

Victory aged nickel pickup on a Republic Parlor Reso guitar.
33 minutes ago
Richard Sundberg liked Clarky's video
39 minutes ago
Scott Schoepf liked Korrigan's photo
51 minutes ago
Scott Schoepf posted a photo

Grandma’s Cigar Box

Under construction, finally found some time to get started.
1 hour ago
Uncle John commented on AGP #'s photo
1 hour ago
Silent Jim posted a video

American Lullabye

CBG composition from Andy S. with SJ and Zane C. 4 string fretted and slide CBGs and Native American flute.
1 hour ago
Uncle John commented on SlowHound's video
Thumbnail

That Fall Feeling 2018

"Wonderful.  So good to hear you.  It's been too long.  D-F#-A-D tuning. …"
1 hour ago
Titch the Clown replied to Brent Kasl's discussion digital tuner
"On mine C is  for chromatic not cello.  This is the most versatile setting  as it…"
1 hour ago
Uncle John commented on BeetleJuice!'s video
Thumbnail

1880's Cigar Box ~Dixieland~ BottleNeck Blues Guitar

"Yas, sir.  As Dave said.  A gentle pleasure."
1 hour ago
Eero Tapani Lehtinen liked Dave Lynas's photo
2 hours ago
Richard Sundberg commented on Richard Sundberg's video
Thumbnail

ROAD WEARY. Downtown Vinnie/ Richard Sundberg

"Well put Dave! The work has started for CALLYFEST, the reunion! Ordering another outhouse,…"
2 hours ago
Dave Lynas commented on Dave Lynas's photo
Thumbnail

Big Dog Slides

"Thanks Beetle, Brian and Uncle John. Old Dogs still dig it!"
3 hours ago

Music

Loading…

© 2018   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service