Looking for advice on doing a build w/ internal springs for a reverb effect.

What kind of spring did you use? Storm door springs seem too heavy / got too much tension to use. Thinking screen door springs? Where did you get your springs? Local hardware store is a bust.

How did you attach the springs to the neck?

Views: 208

Reply to This

Replies to This Discussion

Dollar tree "Echo Mic" has a nice thin wire spring in it! My 2 cents.

Freakin' genius! It's all new to me  - does a piezo pick up the reverb effect? 

Disc Piezo will pick up a nat farting on your CBG! They are basically a microphone/speaker. As a mater of fact the beeper in your microwave, musical cards(birthday, Christmas etc) are Piezo that can be salvaged. You will find that the Piezo will pick up a lot of unwanted noise(drumming your fingers, laying down/picking up the cbc, voice, amp squeal, farting nats) there are several ways to "tame" them. A .001uf capacitor across the leads(sacrifice some of the highs), tone control pot, install a preamp just to name a few. To answer your question. Yes, "Virginia there is a Santa"! But seriously yes the spring reverb will be picked up they also enhance  acoustic guitars natural sound. Imo

Thanks for the info! Nothin’ worse than gassy nats!

Will hafta experiment when I get to the electrification situation part of the fabrication.

Lowes is where I found my springs. You'll need 1.5lbs tension. I've done 5 or 6 and this is an example of the latest one. Yes that big silver thing is a pot lid. Hope this helps you

Nice clean build there! Thanks for the info & an example.

How do you have the lid fastened? A spacer inside with a washer and nut on the back? I use a light spring for the mid to hi and a heavier one for mid to low. Thanks for the tension info.

Lid is attached with one wood screw, I glue a 1 1/2 x 3/4 x 2 wood block to the back of the neck. Then remove the lid handle, I try to find the older lids that have a screw on knob as they seem to work best, also there have been times when I have to notch the bottom of the neck for the lid to fit between the neck and back of the box. My next experiment on this setup will be embedding a piezo in that block that the lid attaches to. Hope that helps. One other note the guitar that has this setup has a warm and comforting  sound that's mid to low similar  to a big body acoustic 6 string

I have a lid like that with a threaded rod for the knob to screw on to, it rings a perfect C.

These are the springs I use, The one on the bottom is from an Echo Mic.

Hi Clint, I am new to the spring thing so proberebly will not contribute much, listen to the others who have had success. But here's my findings so far.

I built this cbg just for testing the spring thang. Like you, not knowing what springs will work best, I started experimenting. What I did was to make the things I tried reversible and variable. 

In this cbg box I have it set up so that I can dampen the springs with a dampener devise operated by the knob on the right, and where you see the sympathetic string tuners I had spring tensioners so as to change the tension of the springs, as I thought that important too.

First springs did not work, possibly too heavy. I Installed the strings you see on this guitar now but they did not work well enough to be audible above the volume of the cbg itself. Then...........A light bulb moment [no pun intended]

I was working at one of my benches that has a desk light fitted into a hole in the wooden top.As I was working, picking up and putting down tools I realised there was a ringing/humming sound coming from some where as I put a tool down on the wooden benchtop. I traced it to the springs on that desk lamp.

The four springs were just the right weight and tension to respond to light tapping on the bench top. CBG reverb at its best I thought, but have not tested further. More demanding things on at the moment.

Photos should tell the story. Even if you haven't got a spare lamp you could test the springs from a lamp and then know what to buy.

Taff

Thanks for the info! May find old lamp @ Goodwill or garage sale.

Quality build btw. Some good craftsmanship right there. The dampening lever is genius! 

Funny thing is that the reason I use the eco Mic spring was years ago I was picking up after my grandson .I threw the toy into the box and I noticed it sounded just like the reverb springs on the old Hammond organ my mom had. When I was looking for springs, I remembered that sound. The other spring "was" a replacement for my industrial magnifying light that I grabbed on a dumpster dive( I dropped and broke the lens, after I bought the springs) I think I got them at ACE.

Taff, I'm intrigued by that sound hole design and markings. Is that Aborigine inspired? Your craftsmanship really sets a high bar to reach for! Even your "test" piece would look good hanging on display.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

Busking Tunes

Started by Donovan in Performances, How to Play, Lessons, Concerts. Last reply by Will "KOOL DOG HOOCH" Bonner 10 hours ago. 3 Replies

PDF DOWNLOAD: How to Build a Hurdy Gurdy

Started by Shane Speal shanespeal.com in Feature Articles. Last reply by Philip Taylor on Thursday. 8 Replies

Pitch Pine

Started by Laurence Owen in Building Secrets, Tips, Advice, Discussion. Last reply by Laurence Owen on Thursday. 4 Replies

Samantha Fish oil can guitar

Started by Kurt Reifert in Building Secrets, Tips, Advice, Discussion. Last reply by Bruno Ballardini on Wednesday. 5 Replies

"Another' lid question.

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner on Wednesday. 10 Replies

Pickup placing

Started by micky rooney in Performances, How to Play, Lessons, Concerts. Last reply by micky rooney on Tuesday. 9 Replies

Blog Posts

Mama Pearson's Soaporium

Posted by Rick Tish on September 14, 2019 at 8:52pm 0 Comments

Fresh Diddley Bow- "Why Not?"

Posted by Glenn Kaiser on September 13, 2019 at 10:23pm 1 Comment

Good weekend selling

Posted by Rick Tish on September 11, 2019 at 10:13pm 0 Comments

Cigar Box Guitar Music - Old time Blues

Posted by John on September 9, 2019 at 6:00pm 2 Comments

The Accidental Canjo

Posted by Poorness Studios on September 8, 2019 at 10:30am 2 Comments

Latest Activity

Anthony Insetta posted a video

1927 Martin 2-17

This Martin guitar is a gift , beautiful full tone love love playing it
22 minutes ago
BUGGY (C) posted a video

Jug band music

Jug band tester
44 minutes ago
Dennis "Denbo" Goodinson commented on Dave Lynas's video
Thumbnail

Cooking Leftovers

"Goose is a beaut! There's always an improvement to make, almost all my builds have been…"
1 hour ago
Dennis "Denbo" Goodinson liked Dave Lynas's video
1 hour ago
Dennis "Denbo" Goodinson liked Steve Holladay's video
1 hour ago
Dennis "Denbo" Goodinson liked Andries D. EKER's video
1 hour ago
Eric Reille joined Mark "Fatt Max" Hill's group
Thumbnail

New Zealand CBG Movement

Kia Ora...Somewhere for all CBG people in the land of the long white cloud to get together and talk…See More
5 hours ago
Josh Thompson liked Dickie's photo
5 hours ago
Eric Reille liked Will Carter's group Australian CBG
7 hours ago
James Pobog posted a discussion

Build #2

Build #2 is underway.Not particularly an original design, but I'm still using these early builds as…See More
7 hours ago
Will "KOOL DOG HOOCH" Bonner liked Taffy Evans's discussion Just off the bench, latest build.
8 hours ago
James Pobog replied to Taffy Evans's discussion Just off the bench, latest build.
"Man, you are SO far out of my league...."
8 hours ago

Music

Loading…

© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->