I have wired a disc piezo and a rod piezo in parallel through a simple active (9V) endpin Jack preamp. I tested it before installing, by tapping them on the table. The disc piezo cane through strong. The rod piezo was faint. I plugged a different rod piezo (by itself) into the preamp, and its signal was strong (as loud as the disc had been).

I thought maybe I had messed the first rod up when wiring it and the disc together. So I took the second rod piezo (the one that tested strong by itself) and soldered it and the disc in parallel, then plugged them into the preamp. This time I took extra care in wiring and soldering them. I am absolutely certain I have wired them correctly, in terms of negative and positive, with no shorts. Same result. The disc signal is loud, but the rod signal is faint.

Is there something about the different signal strengths of discs and rods that makes a rod come through quieter than a disc when wired in parallel through the same preamp?

I don’t know if these details make any difference to the question, but the disc is somewhat oversized (2 inches metal diameter), and the disc is wired with slightly thicker gauge wire than the rod (which is wired via the standard shielded wire with the woven outer shield/ground).

Any ideas?

Views: 158

Reply to This

Replies to This Discussion

It's too early for my brain to properly function, the coffee hasn't kicked in yet and I've got to get out the door and head to work but... I'm guessing it has something to do with the rod piezo being made up of 6 small individual piezos connected in series. So when you add the disk you have a mixed parallel/series network. Why this results in low output of the rod I don't have time to figure out right now... but maybe knowing this will send you down the right path for research.


I thought about the fact that the rod is really several piezo wired in series, but I can’t see how that would cause the rod to be quieter than the disc. After the signal leaves the rod (via the hookup wire in your diagram), the hookup wires from the rod & disk then merge into one wire which plugs into the preamp. In other words, the wiring system looks like a “Y,” with a disc on one fork or branch of the “Y,” and a rod (several piezos in series) on the other branch.

Wiring piezo in series increases the impedance across the whole system, not just the branch of the system where the in series piezo are. So if increased impedance were causing a signal decrease, I would think it should affect both branches in the system (the branch where the disc is as well as the branch where the rod is), not just the branch where the piezos are in series (the rod branch).


The piezo elements used in the Rod type piezo is of a different type. They have less output and less sensitivity than the larger round piezo type.

sounds like the disk is shorting the rod.  If you wire a 100 ohm resister in parallel with a 1 ohm resister, you get a result of 0.99 ohms. perhaps wiring them in series instead?

I’m not sure I follow you about the resistors, but having th tripple-checked and built it twice, swapping out for a new rod the second time, I am confident I have no shorts, bad solder joints, or Reversed polarities.

Since the piezos on each fork or branch of my system (disc on one and rod on the other) are generating their own separate electrical signal separately from each other from the vibration they each respectively experience, Absent some kind of wiring flaw, I don’t see how the electrical signal generated at the end of one branch of the “Y” (the end of the piezo branch) would ever travel into or through the other branch of the “Y” (the disc branch). The disc is not along the piezo signal’s path to ground, and they do not form a loop.

Am I making sense?

If you connect the rod and disk in parallel, any signal created by one travels not only down to the volume pot but also backwards up the other's wire.

think of one as a 12v battery and the other as a 6v battery. 

Correcting a typo:

“I don’t see how the electrical signal generated at the end of one branch of the “Y” (the end of the ROD piezo branch). . .”

Could be the polarity of the disk doesn't match the wire colors? Try switching them.

Rod Piezo's have less output than the round disc type which is why most people use a preamp with the rod piezo. Rod piezo's have less handling noise and less attitude that gives them better acoustic tone.

You could put the round disc piezo in the neck area of your git and the rod piezo in the bridge to give them a more equal performance. You could use a on/on/on 3-way switch to use either or both in parallel. You may also have a preamp bypass lug on your jack to wire up the disc piezo?

This is what I suspected: That discs simply have more output than rods.

Why would putting the disc piezo in the neck area give them a more equal performance? Is that because there is less vibration in the neck (where the disc would be) than in the saddle (where the rod would be)?

partly because the vibrations at the neck would be less than the bridge but mainly because these rods are supposed to be under compression, directly under the bridge piece.

Correct. The string vibration will be stronger at the bridge area and the rod needs to be under string pressure at the bridge.

So you'll be lessening the output for the disc at the neck area and giving the rod piezo the most exposure to try and equal out the output.

Disc piezo at the neck and body junction will have a more mellow/warm tone. Upper low string side of the neck for more bass, lower high string side for more treble.


The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources


Fretless cbg

Started by Caleb D Bennett in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans 16 hours ago. 3 Replies

We build guitars

Started by Wal Callaby in Other stuff - off topic, fun stuff, whatever. Last reply by Jerry Jordan 16 hours ago. 17 Replies

Open Gear Tuners

Started by Brent Kasl in Building Secrets, Tips, Advice, Discussion. Last reply by Jerry Jordan 20 hours ago. 9 Replies

One Finger Lesson: Take Me Home Country Roads - VIDEO & TAB

Started by Shane Speal shanespeal.com in Feature Articles. Last reply by Chuck otto 22 hours ago. 2 Replies

Box fiddle #1

Started by Gervase Gallant in Building Secrets, Tips, Advice, Discussion. Last reply by Gervase Gallant yesterday. 6 Replies

Nut and #1 fret spacing.

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner on Monday. 2 Replies

Zero fret/nut idea

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner on Sunday. 8 Replies

Rescued ss can.

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner on Saturday. 15 Replies

Looking for Builders and Players in Florida!

Started by Will "KOOL DOG HOOCH" Bonner in Fests and Concerts: Organizing and Promoting. Last reply by Will "KOOL DOG HOOCH" Bonner on Thursday. 15 Replies

Fun with a 2x4 Bass - Build Your Own

Started by Shane Speal shanespeal.com in Feature Articles. Last reply by Mike Parker on Thursday. 24 Replies

Blog Posts

A Tale of Two Ukes

Posted by Poorness Studios on June 25, 2019 at 10:00am 1 Comment

Adventures in headstock-making

Posted by Sean Murphy on June 15, 2019 at 4:41pm 2 Comments

site bugs

Posted by the anonymous pick on June 13, 2019 at 8:05pm 6 Comments

Cheesecake Banjolele

Posted by James Matthews on May 21, 2019 at 7:14pm 3 Comments

Latest Activity

Richard Sundberg posted a video

Cigar Box Guitar/Surfing The Partagas Blues

Virtually at the beach playing my UJ Partagas fretless 3 string. Incoming turbulence.
19 minutes ago
T-Gripped liked Cigarbox Slim's photo
39 minutes ago
T-Gripped liked amos's photo
40 minutes ago
T-Gripped commented on Dave Lynas's photo

2 string Fiddles

"Those boxes are wonderful. Getting hard to find the old ones.I really like the carved peg boxes.…"
41 minutes ago
T-Gripped liked Dave Lynas's photo
43 minutes ago
Randy S. Bretz commented on Randy S. Bretz's photo

3 carved bone bridges

"The customer is doing a double neck build using a box that has a name of a pub on it...The Frog and…"
1 hour ago
Uncle John commented on amos's photo

myles 3

"Looks like a player.   Not too fancy, but kind of rich and handsome."
1 hour ago
Uncle John commented on J.Rob's photo


"Your excused. Nice Padron box and a great looking bass."
1 hour ago
Uncle John commented on BeetleJuice!'s photo

Let Freedom Ring out...on a 3 string!

"LOL, Jerry.   Hey, John.  It's to bright for one of my players, you know I like…"
1 hour ago
Uncle John commented on Cigarbox Slim's photo

New Resonator

"I wonder if maybe that is too many sound holes for best acoustic sound. But man, it has the LOOK.…"
1 hour ago
Uncle John commented on Lonman's photo

first bass guitar

"Good look to it.  Kind of ready fro the Fourth Of July - or anything."
1 hour ago
Uncle John commented on J.Rob's video


"Thirty two inch scale!    Sing strainer sound hole.   Oh!  …"
1 hour ago



© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->