As part of this ongoing problematic build, I've attached my headstock to the neck via a scarf joint, with the headstock face creating part of the flat surface of the neck where the fretboard will be attached.

However, in the course of trying to flatten the faces that were glued together, I have gotten the angles slightly out of sync; as a result, there's a slight "valley" in the top third of the neck now. 

Normally I'd just sand down the whole thing to an even flatness, but I need to keep the correct height that I currently have. Is there any way to "patch" the dip?

I've attached a very crude diagram of what I mean (thanks to the original poster who created the diagram I modified).

Views: 71

Reply to This

Replies to This Discussion

Add a flat shim of wood into the glue joint, you can correct the angle by changing the shape of the shim... This fix works, but it's up to you whether you shim or start from scratch.,., I clean the snow off my windshield with a failed neck blank in winter.,.,might make decent kindling too.,., a little shimming, sliding, clamping, and sanding should take care of it.,.,

Hi Sean, ooops! I would suggest glueing a piece of timber to the angled part of the neck, reshape it so that it is now square with enough length for the fresh angle to be cut. Then lay the peghead piece on top of your new timber, line it up so you can draw a line, cut the piece you just added at the correct angle. You could leave room on the side of the cut to level the face of the peghead after if you wanted.

Then  glue the peg head on as you would normally do. Cover this with a veneer on the face if you want to cover the joint.

Hope you can follow this, can't do fancy drawings on here.

Good luck Taff

I would just add a shim and sand that flat.

Hi again Sean, I have a bit more time so I did a drawing of what I meant earlier. 

The way I suggested would give you a shim, as others have said, but will give one with the corrected angle, which is what I thought you wanted to do. Just adding a shim I think will just give the same angle only further back. My suggestion was to replace some wood and recut the angle.

i have also shown the steps I use when cutting a spliced peghead. After the front is sanded flat I then thin the back to get the thickness that suits the tuners.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

Break angle for bridge

Started by Fantacone Box Works in Building Secrets, Tips, Advice, Discussion. Last reply by François 1 hour ago. 10 Replies

Slide off decals

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by François 1 hour ago. 1 Reply

Frets and fretboard

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion on Sunday. 0 Replies

Fret Sides Dressing

Started by Brent Kasl in Building Secrets, Tips, Advice, Discussion. Last reply by Fantacone Box Works on Sunday. 6 Replies

Navigating this forum

Started by Fantacone Box Works in Performances, How to Play, Lessons, Concerts. Last reply by Fantacone Box Works on Sunday. 5 Replies

30.5" scale lay-out help needed please!

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner Jul 6. 15 Replies

Free Cigar Box Tablature Library

Started by Ben "C. B. Gitty" Baker in Performances, How to Play, Lessons, Concerts. Last reply by Brad Schoonmaker Jul 4. 12 Replies

Blog Posts

What wood is this?

Posted by Sean Murphy on July 16, 2019 at 10:48am 0 Comments

apology

Posted by Danny Gordon on July 13, 2019 at 7:30pm 3 Comments

Latest build

Posted by Sean Murphy on July 5, 2019 at 8:34am 5 Comments

Latest Activity

AGP # commented on the anonymous pick's photo
4 minutes ago
AGP # commented on Uncle John's photo
Thumbnail

Swampy and a Rambling Dave Lynas slide with a summer Tee shirt.

""A Finer Threesome You'll Never See"  :-) :-) :-)"
8 minutes ago
AGP # liked Uncle John's photo
12 minutes ago
AGP # commented on Uncle John's video
Thumbnail

Gone Gone Gone

"Another great ole song 'UJ', the Swampy and Yourself in fine voice!, was aware of…"
13 minutes ago
AGP # liked Uncle John's video
29 minutes ago
Darryl Tuttle commented on the anonymous pick's photo
Thumbnail

flurry

"Been there way too many times myself....never gets any easier Sorry my friend for your loss"
33 minutes ago
AGP # liked Clarky's video
43 minutes ago
AGP # commented on Downtown Vinnie's video
Thumbnail

Thingamajiggy

""Good Stuff Vinnie" Rip it Up & Go!  :-)"
45 minutes ago
AGP # liked Downtown Vinnie's video
46 minutes ago
AGP # liked Uncle John's video
57 minutes ago
Keith Rearick liked Uncle John's video
57 minutes ago
Keith Rearick liked cbgkent's video
58 minutes ago

Music

Loading…

© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->