When wiring two piezo in parallel. Are the disks stacked or placed side by side? 

Views: 124

Reply to This

Replies to This Discussion

You could do it either way, but if you stack them , you would have to insulate the back of the top one, right?

I place mine one under the bridge area and the other under the neck area so I guess side by side .. Hope that helps Rat . 

Thanks folks!

Yes BrianQ. I'd have to insulate between them. 

Jeff. I wasn't sure if folks kept them together. Of how far apart they could go. 

Hi Blue rat, the piezos surface has to have a good firm contact with the vibrating surface to work efficiently, the sensor piggy backing the other would not respond well to top vibrations. Insulating  them apart would further decrease efficiency. I have not tried it but that is my understanding.

Taff

Thanks Taffy. Having to insulate between the two would farther dampen it's response. 

I commented on another post on how I will never get that awesome CBG sound out of a quality pup. I have a one pickup guitar build that is glued together but not set up yet. The only good spots I can reach would be directly in front or behind the bridge. 

The back of the guitar is 1/2 plywood. There's less than a 1/2 inch of space between the old door wood and face of the guitar in front of the bridge. And access behind the bridge is tight. Because of the jack support block. That piece of ply marked "E". Yes I mark each piece as it's cut now. Keeps me from cutting a piece out of an already cut piece. Real good at doing that. :) The only other step I'll need to do is drill a third hole for the piezo volume knob. Both pup types will be wired for independent operation so I wont need a switch.  

Hi, in the acoustic six string guitars I build the piezo sensors ,three in total, are recommended by the manufacturer to go under the saddle in between strings 1-2, 3-4 and 5-6 glued to the bridge plate. So the area you mention for your guitar should be good.

Taff

Thanks again Taffy. Any idea of the impedance of three piezo in a row? I was going to slap a Duncan Vintage rail. After getting the idea of finally using piezo the pickup will be the middle pickup from the Fender 69's that'll go into the body I just cut apart. It's output imp is only 6.5. 

SorryBR, I'm not into that sort of info, can't help you there.

Taff

Thanks Taffy. Don't sweat it. Been all over the web looking for info. Haven't found a single direct answer. Yes I understand that an 8 ohm speaker actual ohm reading depends on the frequency going through it. The average is 8 ohms. For a piezo? Not a strait answer or average anywhere. Plenty of charts with lots of X's and Y's. But with no value given to a single one of them. All you end up with is badly spelt words.  I did find out that most upright bass preamps have an impute (the connection between the piezo and preamp ) of 1Mohm. So I can guess with some success that two in parallel will be 500Kohm and three would be ( not quite right ) 330K ohms. And so on. I did read years ago that there is a number of piezo you can't go past. But there was no reason given. 

Hi BR, also maybe the quality of the piezo my affect your calculations, like three off one brand may be different to three of another brand.

Taff

I generally try to place mine close to but on the neck side of the bridge. One just outside of the bass string and one just outside of the high string. I shoot for those spots but often have to move them a little to accommodate sound holes or braces.

Thanks again everyone for your responses. 

What I'll end up doing is first glueing them to a piece of foam. That will be glued to a small piece of ply. Lather to the top sides with lots of hot glue and stick em in place. One shot. 

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

Amp kit

Started by Tim Ahlberg in Performances, How to Play, Lessons, Concerts. Last reply by the anonymous pick 1 hour ago. 4 Replies

Groups or Workshop

Started by john kendall in Building Secrets, Tips, Advice, Discussion. Last reply by the anonymous pick 16 hours ago. 1 Reply

Piezo pup handling noise

Started by Kevin Keating in Building Secrets, Tips, Advice, Discussion. Last reply by Cause the Blue rat yesterday. 5 Replies

CB-stompbox

Started by Jeremy Wade in Building Secrets, Tips, Advice, Discussion. Last reply by the anonymous pick on Sunday. 1 Reply

Neck mortising jig

Started by Rough Cut Tom in Building Secrets, Tips, Advice, Discussion. Last reply by Rough Cut Tom on Wednesday. 2 Replies

Blog Posts

Dual lap steel

Posted by Ron Lutz on January 9, 2020 at 2:42pm 2 Comments

My 3 Gitty Kits

Posted by Poorness Studios on January 8, 2020 at 9:20am 2 Comments

My CBG details

Posted by Paul scofield on January 1, 2020 at 9:22am 2 Comments

Latest Activity

Steebos Kalist liked Poorness Studios's video
9 minutes ago
Cause the Blue rat replied to Tim W's discussion One finger Barre cord technique
"First your fingers do not have to be parallel to the frets. Nor do you have to play a note directly…"
47 minutes ago
Tim W posted a discussion

One finger Barre cord technique

Hi I’m really green with learning CBGs (never played anything with strings before).I’ve done okay…See More
1 hour ago
Tim W updated their profile
1 hour ago
3 String Guitars posted a video

Cigar Box - 3 String Guitar - The Circuit Rider - Red Dog USA

There are several new Cigar Box Guitars for sale at the website https://3-string-guitar.com There is also lots more videos and cigar box blues music songs.
1 hour ago
the anonymous pick commented on smilingdog1's photo
Thumbnail

Contest winners

"well deserved"
1 hour ago
the anonymous pick commented on smilingdog1's photo
Thumbnail

2nd place

"" For a great  "cause " .. ;-)"
1 hour ago
the anonymous pick commented on Jerry Jordan's photo
1 hour ago
the anonymous pick commented on Carl Laman's photo
1 hour ago
the anonymous pick commented on Robbie's photo
1 hour ago
the anonymous pick commented on Robbie's photo
Thumbnail

IMG_0499 (1)

"slick ;-)  "
1 hour ago
the anonymous pick replied to Tim Ahlberg's discussion Amp kit
""Guitar fuel " They have a website and an ebay store  ebay  …"
1 hour ago

Music

Loading…

© 2020   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->