When wiring two piezo in parallel. Are the disks stacked or placed side by side? 

Views: 133

Reply to This

Replies to This Discussion

You could do it either way, but if you stack them , you would have to insulate the back of the top one, right?

I place mine one under the bridge area and the other under the neck area so I guess side by side .. Hope that helps Rat . 

Thanks folks!

Yes BrianQ. I'd have to insulate between them. 

Jeff. I wasn't sure if folks kept them together. Of how far apart they could go. 

Hi Blue rat, the piezos surface has to have a good firm contact with the vibrating surface to work efficiently, the sensor piggy backing the other would not respond well to top vibrations. Insulating  them apart would further decrease efficiency. I have not tried it but that is my understanding.

Taff

Thanks Taffy. Having to insulate between the two would farther dampen it's response. 

I commented on another post on how I will never get that awesome CBG sound out of a quality pup. I have a one pickup guitar build that is glued together but not set up yet. The only good spots I can reach would be directly in front or behind the bridge. 

The back of the guitar is 1/2 plywood. There's less than a 1/2 inch of space between the old door wood and face of the guitar in front of the bridge. And access behind the bridge is tight. Because of the jack support block. That piece of ply marked "E". Yes I mark each piece as it's cut now. Keeps me from cutting a piece out of an already cut piece. Real good at doing that. :) The only other step I'll need to do is drill a third hole for the piezo volume knob. Both pup types will be wired for independent operation so I wont need a switch.  

Hi, in the acoustic six string guitars I build the piezo sensors ,three in total, are recommended by the manufacturer to go under the saddle in between strings 1-2, 3-4 and 5-6 glued to the bridge plate. So the area you mention for your guitar should be good.

Taff

Thanks again Taffy. Any idea of the impedance of three piezo in a row? I was going to slap a Duncan Vintage rail. After getting the idea of finally using piezo the pickup will be the middle pickup from the Fender 69's that'll go into the body I just cut apart. It's output imp is only 6.5. 

SorryBR, I'm not into that sort of info, can't help you there.

Taff

Thanks Taffy. Don't sweat it. Been all over the web looking for info. Haven't found a single direct answer. Yes I understand that an 8 ohm speaker actual ohm reading depends on the frequency going through it. The average is 8 ohms. For a piezo? Not a strait answer or average anywhere. Plenty of charts with lots of X's and Y's. But with no value given to a single one of them. All you end up with is badly spelt words.  I did find out that most upright bass preamps have an impute (the connection between the piezo and preamp ) of 1Mohm. So I can guess with some success that two in parallel will be 500Kohm and three would be ( not quite right ) 330K ohms. And so on. I did read years ago that there is a number of piezo you can't go past. But there was no reason given. 

Hi BR, also maybe the quality of the piezo my affect your calculations, like three off one brand may be different to three of another brand.

Taff

I generally try to place mine close to but on the neck side of the bridge. One just outside of the bass string and one just outside of the high string. I shoot for those spots but often have to move them a little to accommodate sound holes or braces.

Thanks again everyone for your responses. 

What I'll end up doing is first glueing them to a piece of foam. That will be glued to a small piece of ply. Lather to the top sides with lots of hot glue and stick em in place. One shot. 

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

VIDEO FEATURE: Building a micro shop for the work area challenged

Started by KOOL DOG HOOCH in Feature Articles. Last reply by Shane Speal shanespeal.com yesterday. 15 Replies

Latest Activity

Michael Pounds liked Poorness Studios's photo
39 minutes ago
Michael Pounds liked Jack Brady's discussion Join the Discussion: To Put Finish on a Paper Covered Cigar Box... or Not?
52 minutes ago
Taffy Evans commented on James Matthews's blog post Cheesecake Banjolele
"I fully understand James, thanks for responding. Here are a couple of ideas that may help give you…"
53 minutes ago
Fred McNaughton commented on Fred McNaughton's video
Thumbnail

Fish & Chips

"Thanks so much, Dave. I appreciate you giving it a listen."
1 hour ago
Dave Lynas liked Fred McNaughton's video
1 hour ago
Dave Lynas commented on Fred McNaughton's video
Thumbnail

Fish & Chips

"I like this one Fred. Love the one man band sound."
1 hour ago
Dave Lynas commented on AK-77's video
Thumbnail

AK-77 - She Moves Me, Muddy Waters (CBG)

"Excellent. Great sound, Great Guitar play. Clear words. Cool !"
1 hour ago
Derek Rose commented on Derek Rose's video
Thumbnail

After the Sun Goes Down

"Had to change the names and identities to protect the rascally innocents John! I am fine to ride…"
1 hour ago
Dave Lynas liked Derek Rose's video
1 hour ago
Dave Lynas commented on Derek Rose's video
Thumbnail

After the Sun Goes Down

"My new favorite Rose song ! Very good Derek. I love those true story songs."
1 hour ago
Derek Rose commented on Dave Lynas's video
Thumbnail

Chicken Lickin

"Nice blend of instruments Dave. Smooth playing and mixing."
1 hour ago
Derek Rose liked Dave Lynas's video
1 hour ago

Music

Loading…

© 2020   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->