Hey out there, any wiring diagrams on psycho knob install in a guitar with vol.and tone pots? Thanks in advance

Views: 510

Replies to This Discussion

I would imagine that that you install the volume and tone before the psycho knob, the diagramme is from the CB Gitty website

Thank you Jon

I would wire it in between the vol/tone pots and jack.

Okay,I'll try it that way. Thanks

I'm assuming that the psycho knob circuit is input sensitive, meaning it will perform differently at different input levels. If that's the case my thought is it would be better to run the pickup output straight to the psycho knob and wire the tone and volume pot after it. That way the psycho knob circuit is always getting the full direct pickup output and theoretically should have the same sound at any volume setting. I'm certainly no electronic genius and may very well be completely wrong.

It's basically a effect circuit. And most guitar with onboard effects are wired after the pickup vol/tone controls like the way pedal effects come after the pickup controls(if any).

I'm starting to think that wiring the effect before the vol/tone controls would change the level/intensity of the effect more than the pickup, which isn't a bad thing. I see on the schematic that Pickedmoor Jon posted, that there's a area at the bottom labeled: Level. That would be an ideal place to add a Level/Intensity pot to control the strength of the effect in the circuit. That way you could adjust the pickup with your original controls and possibly adjust the effect.

I'd love to see a detailed pic of one of these.

I would disconnect the wires at the jack on your guitar, solder/attach them to the effect and then wire from the effect's output to the jack. Then if you could add a pot for the level, that would be awesome.

Okay, I found a pic of the board. The Level knob is a little block with a set screw to set at one level and leave alone.

If you were good at hacking and soldering without destroying a board, you could remove that block and wire in a pot for extra adjustment benefit.

On the back of the board, there's 3 points to solder the block in. You could remove the block and solder wires there for a pot. Find the ground first and run that to the back of the pot and the 3rd lug. Then just wire up the other 2 to the 1st and 2nd lugs. If it doesn't work well, reverse the 1st and 2nd lug wires and it should work fine. You would probably need a B2k to B10k pot.

Hi Paul

I'm an electrician but not great with electronics yet. I'm also from the UK so we call things by different names, let me see if I get what you are saying. Remove the 10 Kilo ohm variable resistor from the QDD2 board, solder wires from those connections to a new pot of the same value. This will adjust the distortion intensity rather than having a fixed intensity on the overdrive setting of the psycho knob (QDD2), have I got that right? 

On a basic electronics question (as I said I'm a newbie to electronics). A VR or pot has 3 legs, the Input, the fixed Output and the Wiper (variable value resistance) What would the Ground be connected to? I can see that you want an adjustable voltage/amperage so that takes care of the input and wiper but what is the third leg for? Is the ground just for attaching to the chassis of the pot to the QDD2 ground or Guitar?

Thanks in advance to any and all who can help.

Your simply replacing a fixed resistor with the variable type.

The ground goes to lug #3(looking at the bottom of pot-lug will be the one on the far left) which also usually gets grounded to the back or side of the pot and added to the guitars ground circuit.. The far right lug is #1 is signal in.  The middle lug #2 is the wiper.

BTW: if your a lefty - change out lugs #3 and #1 for ccw rotation.

Hope that helps. The fixed position might be best, try it first. Then If you would rather be able to adjust for certain use, you know how to do it. Cheers

I've done a bit of looking around and found these drawings, it gets us a bit closer.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Discussion Forum

Output method

Started by Holly Hodson. Last reply by Tim Pannabecker May 13. 4 Replies

Copper foil tape as shield.

Started by Arthur Payne. Last reply by Arthur Payne May 2. 5 Replies

Why have a switch?

Started by Arthur Payne. Last reply by ILL GREEN Apr 12. 3 Replies

Problem with second-hand amp.

Started by Arthur Payne. Last reply by Arthur Payne Apr 2. 5 Replies

Added the CB Gitty “Psycho Knob”

Started by Tim Pannabecker. Last reply by Paul Craig Mar 8. 16 Replies

Lipstick pickup and Telecaster neck pickup. What goes where?

Started by Slow Blues Dani & Ol' Grey Bear. Last reply by Slow Blues Dani & Ol' Grey Bear Mar 1. 12 Replies

Wiring CB Gitty Black Ice Single Coil

Started by ILL GREEN. Last reply by ILL GREEN Jan 9. 5 Replies

Minimal effect from volume or tone pot

Started by Arthur Payne. Last reply by Paul Craig Dec 21, 2018. 9 Replies

Problem posting discussion

Started by Arthur Payne. Last reply by Paul Craig Dec 17, 2018. 2 Replies

Creackle from Volume and Tone pots

Started by Arthur Payne. Last reply by Arthur Payne Nov 27, 2018. 3 Replies

Vol, tone, 3 way toggle and 2 single coils?

Started by Slow Blues Dani & Ol' Grey Bear. Last reply by Paul Craig Nov 25, 2018. 20 Replies

two picksups - both or separate

Started by Reynhard Boegl. Last reply by Reynhard Boegl Sep 27, 2017. 8 Replies

Psycho knob

Started by bizzaro guitaro. Last reply by bizzaro guitaro Sep 19, 2017. 4 Replies

Psycho knob install

Started by bizzaro guitaro. Last reply by bizzaro guitaro Sep 19, 2017. 13 Replies

Psycho knob

Started by bizzaro guitaro Sep 18, 2017. 0 Replies

I cheated and bought a solderless wiring harness. Naughty boy!

Started by Slow Blues Dani & Ol' Grey Bear. Last reply by Slow Blues Dani & Ol' Grey Bear Aug 18, 2017. 46 Replies

Capacitor

Started by Rose Ericson. Last reply by Rose Ericson Jul 8, 2017. 2 Replies

Wiring A Dual Rail Pickup into A Cbg

Started by Philip Hale. Last reply by Paul Craig Jun 2, 2017. 5 Replies

Buzz or maybe humm

Started by Rose Ericson. Last reply by Paul Craig Mar 12, 2017. 8 Replies

Blog Posts

Cheesecake Banjolele

Posted by James Matthews on May 21, 2019 at 7:14pm 3 Comments

Latest build

Posted by Sean Murphy on May 8, 2019 at 9:03pm 4 Comments

Netherlands Tour

Posted by Dar Stellabotta on May 8, 2019 at 5:33pm 0 Comments

Music

Loading…

© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->