Your Favorite Piezo Tips & Tricks! 
 
Piezo Tip:  "Like a Stomp Box in Your Hands..." With Four Piezos

by Chick Who Tinkers

I use four small piezos straight to jack, no volume or tone. 2 on center under bridge, and one on each side. Super responsive and nice thump when tap it – hand flick makes for beat along with the string playing. Like having a stomp box in your hands while you play.

How to wire it up:
  1. Twist 2 black wires together + the other two black wires together.
  2. Then twist those two doubles together to make all 4 black wires into 1 well connected twist/current.
  3. Then loop on jack + solder - 1 solder easier than multi.
  4. Repeat for red wires.
  5. Hot glue gun to put piezos in place.
Piezos under bridge for strings, and at sides for percussion. Piezos work well in lighter woods, multiple piezos (even fine for small ones), and simple circuits.

 

Piezo Tip:  Reducing "Quackiness" with Capacitors & Resistors

Name: Kirk Bolas
I've experimented with different values of cheap ceramic capacitors and resistors (a basic passive RC network) in order to find a combination of the right values of each that shifts the resonance peak of the piezo' output. The goal was to have a signal the de-emphasized the quackiness of the pickup without making it sound tinny or muffled. The signal is modified before it's "massaged" by any other components. It's not perfect, but it's better than stock sound and cheaper than an expensive preamp. Each pickup is different as is every instrument that it's installed in.

Cable length can have an effect here too. I generally use a 20 ft. cable.

One must experiment with each combination for best results. There's no one-size-fits-all solution.

Views: 3138

Reply to This

Replies to This Discussion

One that I did I recessed the piezo into the through neck and potted it in hot glue. That seemed to do a good job of keeping the squelch down

With disc piezos I tend to mount mine in silicon forward of the bridge and on the low string side.

With rod piezos i sandwich them between the neck and box top at the bridge point.  I've done this with disc piezos as well and it works great too.  With the rod piezos I cut a small channel where its to go thats not quite as deep as the rod is thick. Gets held in place with a piece of masking tape when closing everything up.   

I think the best thing you can do is to coat the top of the piezo disc with hot melt glue.  I think it reduces feedback and improves tone.   Some call doing that 'sandwiching.'   It may be the same as what Slow Sough Guitars means by 'potting'

Placement: best: under or near the neck.  second best: on the neck.  

I have used thin closed cell foam, this also seems to help "movement" noises

The tillman preamps work great, but so do regular acoustic preamps, and mounting them in a box, pedal style (as seen on CBN) is awesome.   They're cheap and come with a Rod piezo.

I have also found that foam mounting tape works great on both sides of the piezo.  Peel and stick!

I used a square of foam the size of the piezo and glue it to the back side of the piezo after installing it. It helps to reduce feedback.

Here’s a layout that will accommodate the “Tillman Preamp”, in fact, it’s a modified version of it? The layout shows it wired through the cbg’s volume pot, it can be omitted for a stand alone unit?

Please respect my work & do not Upload my layouts on Pinterest or any other sites without consent, this is only for us here at the Nation & would like to keep it that way. Thanx :) Enjoy! 

may i ask why there are two volume pots? you are feeding the output  of the first directly into the second in series.. One pot would do the same job..

Master volume effect

Another easy one, this fits in a mint tin with the battery,jacks & volume control,use a 16mm mini pot?

Please respect my work & do not post on any sites without permission, Thanx

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

Preping boxes

Started by White Raven in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans 9 hours ago. 2 Replies

7 Nation Army Variation

Started by Paul Keener in Performances, How to Play, Lessons, Concerts. Last reply by Poorness Studios 17 hours ago. 4 Replies

This month's installment of "WHAT THE HECK IS IT?"

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by the anonymous pick 18 hours ago. 11 Replies

Video.. Building an Evans full acoustic guitar

Started by Taffy Evans in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner 19 hours ago. 7 Replies

couple more pix

Started by James Pobog in Building Secrets, Tips, Advice, Discussion. Last reply by James Pobog yesterday. 3 Replies

Baritone first pix

Started by James Pobog in Building Secrets, Tips, Advice, Discussion. Last reply by Paul Craig on Thursday. 7 Replies

Blog Posts

Tab for Ry Cooder

Posted by Keith Gibson on September 30, 2019 at 12:44pm 2 Comments

Ducktail Run in James Dean Country

Posted by Rick Tish on September 29, 2019 at 9:57pm 1 Comment

Tiki mask guitar

Posted by Phil Stickings on September 27, 2019 at 12:39pm 5 Comments

Festival in the land that time forgot

Posted by Rick Tish on September 23, 2019 at 10:09am 2 Comments

Latest Activity

David Hopkins posted photos
33 minutes ago
Cause the Blue rat replied to James Pobog's discussion Pick guard/cavity cover material
"Thin plywood and now trying masonite. A bit thicker than normal pick guards at between 1/8 to 3/16.…"
1 hour ago
BrianQ. commented on Bill Turner (Wunkyman)'s photo
2 hours ago
Downtown Vinnie posted a video

New Age Beatnick

A Base of One string Bass served with a side of octave one string bass,drenched in a Leslie speaker / Flashback Delay sauce
2 hours ago
the anonymous pick replied to James Pobog's discussion Pick guard/cavity cover material
"Tried , tested, and true  ;-)"
3 hours ago
the anonymous pick commented on Bill Turner (Wunkyman)'s photo
Thumbnail

metal muerte

"Awesome sauce , "
3 hours ago
the anonymous pick left a comment for PEGGY TRAMBLE
"Here are some NS folks ..not sure how many are CAPE  B…"
3 hours ago
smilingdog1 commented on smilingdog1's photo
Thumbnail

Jasons October Entry

"His kit had flush pre - wired mini bucker, 4 pole single pre-wired, 35mm piezo with jack. knobs,…"
3 hours ago
PEGGY TRAMBLE and Ken Vickerson are now friends
4 hours ago
Bill Turner (Wunkyman) posted photos
4 hours ago
3 String Guitars posted photos
4 hours ago
BrianQ. replied to James Pobog's discussion Pick guard/cavity cover material
"Wasn’t gitty selling those vinyl pickguards at one time? I remember Shane did a video about…"
4 hours ago

Music

Loading…

© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->