Starting to think  that  maybe I'm  making my necks too  thick. I think it  carried over  from my 2 string bass (from the free plans). I  start with 2x2 poplar or oak, trim it down to 1 inch, and then  add a fretboard.

Just got Shane's book, and am a little  surprised at his use of 1x2 (3/4 x 1.5) and apparently no added fretboard.

What do  you use?

Views: 186

Reply to This

Replies to This Discussion

try hickory, you can make it thinner and its trong and sounds great!

Might be hard to find near me...

When I began building to sell, I was using 1" thick Walnut, with no fingerboard. I moved on to 3/4" thick with a 1/4" fingerboard. And i used Pine, Poplar, Maple,Cherry, walnut, Spruce, Oak, Mahogany, just whatever was available .,Chestnut, Oak, or Poplar for fingerboards.,  In my opinion it sort of depends on what gauges of strings you plan to use.,.,high strung light gauge, you could use 3/4" Pine with no fingerboard.,., heavier gauges require a little more stiffness.,.,and not all wood is created equal.,.,   did I muddy the water enough.,??

What I'm going for now is 1. the standard "Shane" cbg, tuned Gdg, as well as a setup tuneable to Ebe/Gdg, and fretted pentatonic only (open-3-5-6-7-10-12).

My Home  depot has good stock of hobby wood. The oak 2x2 I got  for the 2 string bass has awesome  grain. The walnut fretboards have some  nice figure sometimes. Varathane Ipswich Pine stain on oak and walnut. Is pretty  damn cool looking. The oak goes golden and the  walnut goes nice and warm.

Do any of you use rout round-over bits on the neck to contour the back a bit?

Yes, 1/2”

I have used a Harbor Freight hand held router with a 1/2" round over bit since day one several years and 65 guitars ago.. Takes a while to get a handle on it but works like a charm. You have to move in the right direction though i.e. from where the neck attaches to the body up to the headstock and then back the other side from the headstock to the body. Of course all of this is done before the neck is attached to the body. You have to figure out now to avoid nasty gouges from a bit that is REALLY spinning and shreds so much wood off you think you are a woodchuck or maybe a beaver or even a woodpecker! You have to do some finishing with a file at the neck and the body. You also have to learn to set the bit at the proper depth so that the roundoff of the back of the neck is more or less perfect. I also ALWAYS glue a fretboard on the neck for extra strength. So far no complaints from customers. Good luck!

I have a Ryobi router that I use, and a router table that I have yet to set up. Last build I used it but that neck is still a little thick (1 inch with 1/4" fretboard). That one was a 1" diameter roundover, and I just ordered a 1.5" .

Hi James, my necks are 1" , 25mm, overall including the hardwood fingerboard.

I select my timber with grain oriented as in the photo, for stability. I use a 1/2" round over bit with bearing. I prefer to move the material rather than the router so I clamp the trimmer as shown in the photo. If doing a larger round over I would suggest taking smaller bites at a time so as to minimise any tearout. 

This method works well if you have a peghead that kicks back or a heal on the neck.

Taff

I have a router table that I  haven't set up yet,  but will soon. Agree with  grain  direction.

Bunnings Tassie Oak Taff? lol

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor


Recommended Links & Resources


Forum

Rocky Patel mocked up

Started by James Pobog in Building Secrets, Tips, Advice, Discussion. Last reply by James Pobog 29 seconds ago. 2 Replies

Chords

Started by Mitchell Cutsinger in Performances, How to Play, Lessons, Concerts. Last reply by BrianQ. 13 minutes ago. 1 Reply

First build

Started by Lark Leazar in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans 17 hours ago. 35 Replies

Headless Guitar Project - a $100 eBay kit & Gitty pickups

Started by Cigar Box Nation in Feature Articles. Last reply by Poorness Studios on Thursday. 5 Replies

Cigar Box Amp Mods

Started by Cigar Box Nation in Feature Articles. Last reply by RTZGUITARS Sep 17. 14 Replies

Blog Posts

Prototyping with a big ol' wine box

Posted by Ben on September 23, 2021 at 4:00pm 0 Comments

Mr. Bells

Posted by Stephen Cohen on September 4, 2021 at 12:30pm 0 Comments

Bookie's Poor Man's Dobro

Posted by Steve Bookout on July 18, 2021 at 2:04pm 7 Comments

Get your groove on for free

Posted by François on July 13, 2021 at 3:05pm 1 Comment

Latest Activity

James Pobog replied to James Pobog's discussion Rocky Patel mocked up
"The back of the box is just plain, but here's the back of the neck..."
30 seconds ago
Doug Thorsvik posted a video

Pontoon: 3-String (G1G2D3) Cigar Box Guitar

Cigar Box Guitar Slingers - Spokane, 75th Zoom Mtg Sep 27, 2021. More info and free songbooks: https://sites.google.com/site/cigarboxguitarslingersspokane/home
6 minutes ago
BrianQ. commented on smilingdog1's video
Thumbnail

John Seabuagh and Heather Carter, here at the Hwy61roadhouse 2021 cigar box guitar festival.

"Thanx for this, it’s been such awhile since we’ve had festival videos here!!"
8 minutes ago
BrianQ. liked Poorness Studios's video
10 minutes ago
BrianQ. replied to Mitchell Cutsinger's discussion Chords
"Nothing, keep practicing!"
13 minutes ago
BrianQ. replied to Steve Bookout's discussion Double Necked E-lectric Whachamacallit
"Kool, in the 50’s, Mosrite made a double-neck for Joe Maphis that had a Mando on top &…"
14 minutes ago
BrianQ. replied to Luke Jalbert's discussion Building a Cigar Box guitar with no musical parts
19 minutes ago
Luke Jalbert replied to Luke Jalbert's discussion Building a Cigar Box guitar with no musical parts
1 hour ago
Doug Thorsvik commented on Poorness Studios's photo
Thumbnail

Jewelry Box to Guitar Amp

"Probably next year Kale! The Slingers will be performing live for the first time at the Spokane…"
1 hour ago
Carl Floyd liked Taffy Evans's discussion The hidden Volume pot, revealed
3 hours ago
Carl Floyd liked Steve Bookout's discussion Double Necked E-lectric Whachamacallit
3 hours ago
Uncle John replied to Steve Bookout's discussion Double Necked E-lectric Whachamacallit
"Hunh.   Nylon 4 and metal 3.   Makes sense.   Different colored necks…"
4 hours ago

Music

© 2021   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->