i built my first resonator using a spun aluminum cone and was happy with the sound and tone however I didn’t have the right size screws to mount the steel cover at first. Once I did get the cover on it seemed the volume and maybe the tone had been reduced. The cone just sits on the top and without the cover is held there by the tension from the saddle the same as in a normal guitar. The cover screws go through the lip of the cone and so hold it tight to the top. I am going to take the top off and make sure I can hear the difference. If so I will either leave it off, make a small bridge of sheet metal over the bridge to rest my hand on or maybe build a lip or sound cone to support the cone the same as a full size guitar.  My question is has anyone else found using traditional setup of the cone to help with volume and resonance compared to attaching the cone with screws or bolts to the top? Just opinions welcomed also  thanks

Views: 56

Reply to This

Replies to This Discussion

I personally wouldn't use the type of cone that screws to the top. The whole point of a reso cone is that it floats on the lip of a tone ring (or sound well). Not being connected - screwed or glued to anything - allows the cone to do what the name implies . . . resonate.

A tone ring is very easy to build out of baltic birch plywood, and easy to install. Here's a link with far more info than you could ever want. Though aimed at traditional guitars, the same principle applies to putting a reso cone in a cigar box.

http://www.hangoutstorage.com/resohangout.com/storage/attachments/a...

Some years back when people started making them, I did experiment with one of those cones that screws to the top. Was not impressed. The tone and volume level is night day between those and a traditional cone/installation

Hi Robert, yes to what Blind Doughboy has said. I also place the cone in position, push down on the centre (bridge position) so simulate string pressure, then with the other hand I tap around the cone where it contacts the top using a finger, so as to highlite any areas of none contact.

Taff

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

Day 1: Whiskey Tin Diddley Bass

Started by JP Lace Master in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner 1 minute ago. 1 Reply

Break angle for bridge

Started by Fantacone Box Works in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans 28 minutes ago. 1 Reply

Frets and fretboard

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion yesterday. 0 Replies

Fret Sides Dressing

Started by Brent Kasl in Building Secrets, Tips, Advice, Discussion. Last reply by Fantacone Box Works yesterday. 6 Replies

Navigating this forum

Started by Fantacone Box Works in Performances, How to Play, Lessons, Concerts. Last reply by Fantacone Box Works yesterday. 5 Replies

30.5" scale lay-out help needed please!

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner Jul 6. 15 Replies

Free Cigar Box Tablature Library

Started by Ben "C. B. Gitty" Baker in Performances, How to Play, Lessons, Concerts. Last reply by Brad Schoonmaker Jul 4. 12 Replies

Blog Posts

apology

Posted by Danny Gordon on July 13, 2019 at 7:30pm 3 Comments

Latest build

Posted by Sean Murphy on July 5, 2019 at 8:34am 5 Comments

A Tale of Two Ukes

Posted by Poorness Studios on June 25, 2019 at 10:00am 2 Comments

Latest Activity

Don Craig liked Allan jay Palermo's photo
3 minutes ago
Glenn Kaiser posted photos
5 minutes ago
Glenn Kaiser posted a status
"Ok, position markers in place- done!"
7 minutes ago
Will "KOOL DOG HOOCH" Bonner commented on Sean Murphy's blog post Overpriced cigar box in antique store?
"I had a summer job during high school(many,many,many moons ago) in a cigar factory. They last a…"
10 minutes ago
Taffy Evans replied to Fantacone Box Works's discussion Break angle for bridge
"Hi Fantacone, my thought is just make the bridge high enough to get the best break angle to the…"
28 minutes ago
Taffy Evans commented on Sean Murphy's blog post Overpriced cigar box in antique store?
"Hi Will, oh! I thought cigars might get better over time like good wine. Sean, that crack would not…"
38 minutes ago
Larry Cuddy commented on Larry Cuddy's photo
Thumbnail

IMG_2446

"Derek, thanks for the comments on the guitar necks, I hit the wrong button and it got deleted.…"
39 minutes ago
Downtown Vinnie posted a video
1 hour ago
Derek Rose commented on Uncle John's photo
Thumbnail

100_2041

"Keep movin' hobo!"
1 hour ago
Derek Rose liked Uncle John's photo
1 hour ago
Derek Rose liked Larry Cuddy's photo
1 hour ago
Derek Rose liked Larry Cuddy's photo
1 hour ago

Music

Loading…

© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->