i built my first resonator using a spun aluminum cone and was happy with the sound and tone however I didn’t have the right size screws to mount the steel cover at first. Once I did get the cover on it seemed the volume and maybe the tone had been reduced. The cone just sits on the top and without the cover is held there by the tension from the saddle the same as in a normal guitar. The cover screws go through the lip of the cone and so hold it tight to the top. I am going to take the top off and make sure I can hear the difference. If so I will either leave it off, make a small bridge of sheet metal over the bridge to rest my hand on or maybe build a lip or sound cone to support the cone the same as a full size guitar.  My question is has anyone else found using traditional setup of the cone to help with volume and resonance compared to attaching the cone with screws or bolts to the top? Just opinions welcomed also  thanks

Views: 56

Reply to This

Replies to This Discussion

I personally wouldn't use the type of cone that screws to the top. The whole point of a reso cone is that it floats on the lip of a tone ring (or sound well). Not being connected - screwed or glued to anything - allows the cone to do what the name implies . . . resonate.

A tone ring is very easy to build out of baltic birch plywood, and easy to install. Here's a link with far more info than you could ever want. Though aimed at traditional guitars, the same principle applies to putting a reso cone in a cigar box.

http://www.hangoutstorage.com/resohangout.com/storage/attachments/a...

Some years back when people started making them, I did experiment with one of those cones that screws to the top. Was not impressed. The tone and volume level is night day between those and a traditional cone/installation

Hi Robert, yes to what Blind Doughboy has said. I also place the cone in position, push down on the centre (bridge position) so simulate string pressure, then with the other hand I tap around the cone where it contacts the top using a finger, so as to highlite any areas of none contact.

Taff

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

Frets and fretboard

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion yesterday. 0 Replies

Fret Sides Dressing

Started by Brent Kasl in Building Secrets, Tips, Advice, Discussion. Last reply by Fantacone Box Works yesterday. 6 Replies

Navigating this forum

Started by Fantacone Box Works in Performances, How to Play, Lessons, Concerts. Last reply by Fantacone Box Works yesterday. 5 Replies

30.5" scale lay-out help needed please!

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner Jul 6. 15 Replies

Free Cigar Box Tablature Library

Started by Ben "C. B. Gitty" Baker in Performances, How to Play, Lessons, Concerts. Last reply by Brad Schoonmaker Jul 4. 12 Replies

Nut and #1 fret spacing.

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Jul 2. 11 Replies

Blog Posts

apology

Posted by Danny Gordon on July 13, 2019 at 7:30pm 3 Comments

Latest build

Posted by Sean Murphy on July 5, 2019 at 8:34am 5 Comments

A Tale of Two Ukes

Posted by Poorness Studios on June 25, 2019 at 10:00am 2 Comments

Latest Activity

Allan jay Palermo posted photos
4 minutes ago
Glenn Kaiser posted a photo

gkDoubleDiddleyBow

Double Diddley, bass string on one neck, plain heavy git string on the other
22 minutes ago
Blues Frog commented on Smokin' Guitars's photo
Thumbnail

Dog Bone 1

"I like this one alot! Very cool build."
24 minutes ago
Blues Frog replied to Smokin' Guitars's discussion Smokin' Guitars - New Member Introduction in the group Introduce Yourself!
"Started building in 2015 for something new to do. Joined this site because the folks here are…"
25 minutes ago
Uncle John posted a photo
30 minutes ago
Taffy Evans replied to Paul Craig's discussion What's on your workbench?
"Hi Mark, the patches are spruce and glued with the grain going across the seam for strength. Yep,…"
32 minutes ago
Uncle John posted a video
44 minutes ago
Larry Cuddy posted photos
2 hours ago
Larry Cuddy updated their profile
2 hours ago
Ricky liked Uncle John's video
2 hours ago
AGP # posted photos
2 hours ago
Glenn Kaiser posted a status
2 hours ago

Music

Loading…

© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->