I have nearly wired in my first CBG but just want to make  sure it is right. 

 I have soldered the capacitor to the left hand leg/solder post on the tone pot (as viewed from the back with legs facing upwards)  As I see  this on a diagram however many videos I watch seem to show the capacitor being wired to the middle leg on the tone pot. 

 Does it matter which leg the capacitor goes to on the tone pot? 

Also I am using a tin box for the top and my mini humbucker is cut into the top of the tin but is touching the tin, will this cause any problems? The pots and Jack are also attached directly to the tin lid so wondered how this might effect the ground or cause ground problems or is this OK? 

Any help with these issues would be much appreciated

Views: 113

Reply to This

Replies to This Discussion

This is the diagram I have followed.. 

I totally agree with Pick on the tin top. Washers or blocks... even some electrical tape could do wonders in a situation like this.

As for the question about the tone pot, it doesn't really matter how you wire it as long as the middle lug is used somehow. Some people swear by doing it the way in the diagram above, others put the capacitor between the two pots (like the diagram below). It really doesn't matter as long as the signal goes thru the capacitor/pot then to ground.

Depending on the  amount of  "metal" in the  "tin".  you may need to separate the  pickup  , pots, and  jack from any direct contact with  the tin .  ie: rubber washers , and  wood block mounting the  pickup. etc . if your pickup touches  the tin , it may  make the entire top act like a pickup , and sound like a piezo .. then again , you may like that sound ,  and it  may accent the  tin  reso  better .. then again .. maybe not .  .In my opinion ,  it is best to always separate , but  if you build it so you can test  both ways with out obligation,  you can  decide your self .  ;-)

 hope that helps .

 

Thanks, after I string it up i will test it and see what happens, I did plug it in and it tapped the top of the tin and it sounded a bit like a stomp box drum so I guess the whole top is acting like a pickup as it is.
The volume knob worked but the tone didn't seem to do anything although I couldn't really tell when tapping it like a drum.
If I was to use washers to isolate the Jack and pots would I also need to make the hole bigger so the shafts doesn't touch when going through the tin? I did read somewhere that tin tops actually help with the wiring as the tin grounds everything for you.
Should I try isolating only the pickup first with a wood/plastic surround?

It's just better to isolate  everything everywhere  (shafts included) . There is a chance that your "tin" contains more aluminum  than metal , so even if you   incorporated the lid as a ground , it wouldnt work well in that case , And if it is more "metal" than tin or aluminium , The pickup field would change or  be run through the whole top , and you risk weird  loop issues etc .. with the pots and jack.  etc etc etc . 

Actually it does matter what lug your cap is soldered too. The good news is they both work. But they will sound and work slightly different. Try it one way. Then try it the other. 

Anonymous gave great advice. Isolate! 

thanks for the help I have mounted the humbucker into the plastic case it came with so is now not touching any metal. I have not yet isolated the pots or jack as wanted to see how it would sound and it is all working well including the tone control.

However it does seem to sound like it has a lot of delay or reverb (not sure which as this is all new to me)  ie if I strum the open high G it rings out for a good 7 seconds and drowns out any tune i am playing is this normal ? or could this be due to not isolating the pots from the tin?

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

Volume/Tone Pots

Started by Brent Kasl in Building Secrets, Tips, Advice, Discussion. Last reply by Cause the Blue rat yesterday. 4 Replies

CONTEST CANCELLED: We Need Your Photos!

Started by Shane Speal shanespeal.com in Feature Articles. Last reply by Alex Fong on Friday. 2 Replies

Mods to CBG kit

Started by James Pobog in Building Secrets, Tips, Advice, Discussion. Last reply by James Pobog on Wednesday. 4 Replies

s/s lm386 draw amp,

Started by GARAGE HERMIT in Building Secrets, Tips, Advice, Discussion. Last reply by Paul Craig on Wednesday. 8 Replies

Latest Activity

Order99 liked Bill Turner (Wunkyman)'s photo
2 minutes ago
Derek Rose commented on Uncle John's video
Thumbnail

Pawn Shop Christmas Commercial

"hehe! Hey Unc, I accidently left a can of Vienna sausages in my pants pocket in the dryer and now…"
1 hour ago
Derek Rose liked Uncle John's video
1 hour ago
BrianQ. liked Glenn Kaiser's blog post New Diddley and Song for CBN Christmas Project too :)
1 hour ago
BrianQ. commented on Glenn Kaiser's photo
Thumbnail

MontecristoDiddley

"Way kool, Glenn"
1 hour ago
Derek Rose liked AGP #'s video
1 hour ago
Derek Rose commented on AGP #'s video
Thumbnail

"Rollin' 'n' Tumblin' Blues"

"Lots of beefy tone from that slab Alan. Nice smooth and accurate sliding."
1 hour ago
BrianQ. commented on cbgkent's video
Thumbnail

How to remove unwanted stickers easily

"Informative, good to see you, been a bit :D"
2 hours ago
BrianQ. commented on Dave Lynas's photo
Thumbnail

Sunday Morning Duke

"The Duke commands attention!"
2 hours ago
BrianQ. liked Dave Lynas's photo
2 hours ago
Derek Rose commented on Poorness Studios's video
Thumbnail

Into The Mystic on CBG

"Excellent cover Poorness. One of my favorites by Van. I do this one too, on a 3 in DAd and on a std…"
2 hours ago
Derek Rose liked Poorness Studios's video
2 hours ago

Music

Loading…

© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->