Any other methods or tools recommended besides the cbgitty 35' angle beveling tool for clean edges?

Views: 198

Reply to This

Replies to This Discussion

I have not seen the Gitty  tool but the ways I do it are a file I mounted in a block of wood at an angle, don't use that much, a file mounted to a block of wood, not angled it's the one I prefer, and I do it free hand. 

On a cigar box fingerboard I do it quickly on my belt sander. I nip the fret ends flush, sand smooth on the beltsander then bevel the top ends of the frets the same way. I do this before gluing the fingerboard to the neck.

I then remove any sharp corners with a special file (or small 3 corner file will do) then level the frets and recrown as required and polish. With a flat narrow cbg fingerboard levelling ect, is minimal though, I find.

Taff

The belt sander is the same way i do it. I just put it in my vise. Then i finish with a little hobby 2 sided file that i filed one edge smooth so as not to scratch the board

I've always just used a fine mill file freehand. I hear the 3 sided file was the choice of pro's for years.,.,usually quality fine grit sandpaper works for me..

Hi Jerry, I was referring to the corners that can catch your hand on the fret ends. I have a very small fine file for this job, sandpaper would not get into that corner.

I think you may be referring to the old way of recrowning the fret tops, and then sandpaper. I find it best to use proper crowning files and wet n dry paper for that. But not on cbgs.

Taff

Stew Mac sells a small fret dressing file that works very well for smoothing out those edges that feel so sharp. The main difference in the file is that is is smooth on the two thin edges so you can round a fret edge without gouging into your fret board. Nice little took for cheap. End Dressing File

Yes Tom that's the one I use now. Although I have made my own over the years by grinding a safe edge on both sides of  needle files.

Taff

here in Arkansas with humidity changes, the fret tangs are what had been giving me trouble.  What I have been doing lately and seems to work great is to cut the frets to length and then nip the ends of the tang at an angle, then install the frets as normal.  Seems to have solved my particular problem.

I have tried the pre-cut semihemispherical end method. You basically cut and shape the fret ends before you install them. A good tip on a tapered neck is to start on the wide end and work your way up the neck. That way if you cut one a little short,  odds are you can use it further up the fret board. 

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

Latest Activity

Dennis "Denbo" Goodinson liked Dave Lynas's photo
2 hours ago
Dennis "Denbo" Goodinson commented on Dave Lynas's photo
Thumbnail

Chicken Guitar

"That's a great pic showing some of his future coop-mates"
2 hours ago
Dennis "Denbo" Goodinson liked Dave Lynas's photo
2 hours ago
KOOL DOG HOOCH replied to KOOL DOG HOOCH's discussion Building a micro shop for the work area challenged!!
"What a monster! What does the that weigh 300lbs? I wouldn't have storage or the ability to…"
5 hours ago
Taffy Evans replied to KOOL DOG HOOCH's discussion Building a micro shop for the work area challenged!!
"Hi Hooch, ha ha, it was in the yard of a place I worked at, not being used, big old cast iron type…"
5 hours ago
the anonymous pick replied to Mellowmuso87's discussion Resources for Australian cigar Box guitar builders!
"Here's over 900  members ,…"
6 hours ago
Myron Joe Hickel liked Randy S. Bretz's video
7 hours ago
KOOL DOG HOOCH replied to KOOL DOG HOOCH's discussion Building a micro shop for the work area challenged!!
"Lol That means I'd have to drag the washer outside and do a load of laundry while running the…"
8 hours ago
Doug Krantz replied to KOOL DOG HOOCH's discussion Building a micro shop for the work area challenged!!
"could run a pony belt off the washer to power the sander"
8 hours ago
KOOL DOG HOOCH replied to KOOL DOG HOOCH's discussion Building a micro shop for the work area challenged!!
"36" cut with a 2" blade! What did you do start a saw mill?"
9 hours ago
KOOL DOG HOOCH replied to KOOL DOG HOOCH's discussion Building a micro shop for the work area challenged!!
"I started making one of these but ran into a major snag half way into the build. The wife got…"
9 hours ago
Greg Tiffany commented on BUGGY (C)'s video
Thumbnail

Old Dutch

"Looks like a Corvair. Great Tune about a great car,"
9 hours ago

Music

Loading…

© 2020   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->