Any other methods or tools recommended besides the cbgitty 35' angle beveling tool for clean edges?

Views: 167

Reply to This

Replies to This Discussion

I have not seen the Gitty  tool but the ways I do it are a file I mounted in a block of wood at an angle, don't use that much, a file mounted to a block of wood, not angled it's the one I prefer, and I do it free hand. 

On a cigar box fingerboard I do it quickly on my belt sander. I nip the fret ends flush, sand smooth on the beltsander then bevel the top ends of the frets the same way. I do this before gluing the fingerboard to the neck.

I then remove any sharp corners with a special file (or small 3 corner file will do) then level the frets and recrown as required and polish. With a flat narrow cbg fingerboard levelling ect, is minimal though, I find.

Taff

The belt sander is the same way i do it. I just put it in my vise. Then i finish with a little hobby 2 sided file that i filed one edge smooth so as not to scratch the board

I've always just used a fine mill file freehand. I hear the 3 sided file was the choice of pro's for years.,.,usually quality fine grit sandpaper works for me..

Hi Jerry, I was referring to the corners that can catch your hand on the fret ends. I have a very small fine file for this job, sandpaper would not get into that corner.

I think you may be referring to the old way of recrowning the fret tops, and then sandpaper. I find it best to use proper crowning files and wet n dry paper for that. But not on cbgs.

Taff

Stew Mac sells a small fret dressing file that works very well for smoothing out those edges that feel so sharp. The main difference in the file is that is is smooth on the two thin edges so you can round a fret edge without gouging into your fret board. Nice little took for cheap. End Dressing File

Yes Tom that's the one I use now. Although I have made my own over the years by grinding a safe edge on both sides of  needle files.

Taff

here in Arkansas with humidity changes, the fret tangs are what had been giving me trouble.  What I have been doing lately and seems to work great is to cut the frets to length and then nip the ends of the tang at an angle, then install the frets as normal.  Seems to have solved my particular problem.

I have tried the pre-cut semihemispherical end method. You basically cut and shape the fret ends before you install them. A good tip on a tapered neck is to start on the wide end and work your way up the neck. That way if you cut one a little short,  odds are you can use it further up the fret board. 

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

Today's progress 9/22/19

Started by James Pobog in Building Secrets, Tips, Advice, Discussion. Last reply by Poorness Studios 31 minutes ago. 2 Replies

My Obsession

Started by Del Puckett in Performances, How to Play, Lessons, Concerts. Last reply by Will "KOOL DOG HOOCH" Bonner 21 hours ago. 4 Replies

Info please.

Started by James Pobog in Building Secrets, Tips, Advice, Discussion. Last reply by Andries D. EKER 23 hours ago. 11 Replies

Hollow construction?

Started by James Pobog in Building Secrets, Tips, Advice, Discussion. Last reply by Andries D. EKER yesterday. 7 Replies

Sigh........

Started by James Pobog in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner on Friday. 4 Replies

Sigh........

Started by James Pobog in Building Secrets, Tips, Advice, Discussion. Last reply by James Pobog on Thursday. 2 Replies

Nuts

Started by James Pobog in Building Secrets, Tips, Advice, Discussion. Last reply by BrianQ. on Thursday. 6 Replies

Another idea...

Started by James Pobog in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner on Thursday. 3 Replies

Yeah, OK,...

Started by James Pobog in Other stuff - off topic, fun stuff, whatever. Last reply by Will "KOOL DOG HOOCH" Bonner on Thursday. 9 Replies

Shovel guitar and sizes

Started by Laurence Owen in Building Secrets, Tips, Advice, Discussion. Last reply by Laurence Owen on Tuesday. 5 Replies

Blog Posts

Mailing boxes for CBG's

Posted by Kevin Patrick on September 18, 2019 at 10:02am 4 Comments

So...

Posted by Emer M. on September 16, 2019 at 11:59am 0 Comments

Mama Pearson's Soaporium

Posted by Rick Tish on September 14, 2019 at 8:52pm 0 Comments

Latest Activity

Dave Lynas commented on Dave Lynas's video
Thumbnail

Hohner Special 20 and the Goose

"It does have a good cross harp sound. A Marine Band with attitude Uncle."
1 hour ago
Jeff 'Bones' Reilly commented on Jeff 'Bones' Reilly's photo
Thumbnail

#4 Commissioned Build

"You know me to well AGP I’m always left of  can’t bring myself to a central neck…"
3 hours ago
the anonymous pick replied to James Pobog's discussion Today's progress 9/22/19
"love the electric conduit :-)"
4 hours ago
Dennis "Denbo" Goodinson liked Dave Lynas's video
4 hours ago
Dennis "Denbo" Goodinson liked Korrigan's photo
4 hours ago
Dennis "Denbo" Goodinson liked Korrigan's photo
4 hours ago
Dennis "Denbo" Goodinson liked Korrigan's photo
4 hours ago
Dennis "Denbo" Goodinson liked Vern Hallett's photo
4 hours ago
Dennis "Denbo" Goodinson liked Vern Hallett's photo
4 hours ago
Dennis "Denbo" Goodinson liked Vern Hallett's photo
4 hours ago
James Pobog posted a discussion

Today's progress 9/22/19

Got stuff done, but not as much as I wanted, had some damage control to think through...Right…See More
5 hours ago
Myron Joe Hickel replied to GARAGE HERMIT's discussion my diy table saw, it's not for the squeamish,
"Now that bring back memories. Back in the late 70's early 80's I use to buy a…"
6 hours ago

Music

Loading…

© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->