Any other methods or tools recommended besides the cbgitty 35' angle beveling tool for clean edges?

Views: 167

Reply to This

Replies to This Discussion

I have not seen the Gitty  tool but the ways I do it are a file I mounted in a block of wood at an angle, don't use that much, a file mounted to a block of wood, not angled it's the one I prefer, and I do it free hand. 

On a cigar box fingerboard I do it quickly on my belt sander. I nip the fret ends flush, sand smooth on the beltsander then bevel the top ends of the frets the same way. I do this before gluing the fingerboard to the neck.

I then remove any sharp corners with a special file (or small 3 corner file will do) then level the frets and recrown as required and polish. With a flat narrow cbg fingerboard levelling ect, is minimal though, I find.


The belt sander is the same way i do it. I just put it in my vise. Then i finish with a little hobby 2 sided file that i filed one edge smooth so as not to scratch the board

I've always just used a fine mill file freehand. I hear the 3 sided file was the choice of pro's for years.,.,usually quality fine grit sandpaper works for me..

Hi Jerry, I was referring to the corners that can catch your hand on the fret ends. I have a very small fine file for this job, sandpaper would not get into that corner.

I think you may be referring to the old way of recrowning the fret tops, and then sandpaper. I find it best to use proper crowning files and wet n dry paper for that. But not on cbgs.


Stew Mac sells a small fret dressing file that works very well for smoothing out those edges that feel so sharp. The main difference in the file is that is is smooth on the two thin edges so you can round a fret edge without gouging into your fret board. Nice little took for cheap. End Dressing File

Yes Tom that's the one I use now. Although I have made my own over the years by grinding a safe edge on both sides of  needle files.


here in Arkansas with humidity changes, the fret tangs are what had been giving me trouble.  What I have been doing lately and seems to work great is to cut the frets to length and then nip the ends of the tang at an angle, then install the frets as normal.  Seems to have solved my particular problem.

I have tried the pre-cut semihemispherical end method. You basically cut and shape the fret ends before you install them. A good tip on a tapered neck is to start on the wide end and work your way up the neck. That way if you cut one a little short,  odds are you can use it further up the fret board. 


The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources


Logo using tracing paper

Started by Titch the Clown in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner 2 hours ago. 3 Replies

Yeah, OK,...

Started by James Pobog in Other stuff - off topic, fun stuff, whatever. Last reply by Will "KOOL DOG HOOCH" Bonner 2 hours ago. 7 Replies

Info please.

Started by James Pobog in Building Secrets, Tips, Advice, Discussion. Last reply by James Pobog 7 hours ago. 3 Replies

Build #2

Started by James Pobog in Building Secrets, Tips, Advice, Discussion. Last reply by Poorness Studios yesterday. 3 Replies

PDF DOWNLOAD: How to Build a Hurdy Gurdy

Started by Shane Speal in Feature Articles. Last reply by Philip Taylor Sep 12. 8 Replies

Blog Posts

Mailing boxes for CBG's

Posted by Kevin Patrick on September 18, 2019 at 10:02am 4 Comments


Posted by Emer M. on September 16, 2019 at 11:59am 0 Comments

Mama Pearson's Soaporium

Posted by Rick Tish on September 14, 2019 at 8:52pm 0 Comments

Fresh Diddley Bow- "Why Not?"

Posted by Glenn Kaiser on September 13, 2019 at 10:23pm 1 Comment

Latest Activity

Josh Thompson liked Poorness Studios's blog post The Best Jugs in Kentucky Are Empty
5 minutes ago
Josh Thompson commented on Josh Thompson's photo

Tempus Cigar Box Guitar

"Thanks everyone"
9 minutes ago
Josh Thompson liked Josh Thompson's photo
9 minutes ago
Thomas Case liked Preston J. Laisure's photo
45 minutes ago
Thomas Case liked Lapsteel washboard's photo
46 minutes ago
Thomas Case liked Lapsteel washboard's photo
47 minutes ago
Thomas Case commented on Thomas Case's photo

Build #20, 5th mandolin

"Thanks Poorness"
53 minutes ago
Will "KOOL DOG HOOCH" Bonner replied to Titch the Clown's discussion Logo using tracing paper
"Thank you for the heads up! I've been using my electric  label maker with clear labels in…"
2 hours ago
Will "KOOL DOG HOOCH" Bonner replied to James Pobog's discussion Yeah, OK,...
"LOL, for sure!"
2 hours ago
Dave Lynas posted videos
4 hours ago
Titch the Clown commented on Kevin Patrick's blog post Mailing boxes for CBG's
"I make a trip to my local recycling depot and get a big box I can cut up to make my own shipping…"
4 hours ago
Titch the Clown replied to Titch the Clown's discussion Logo using tracing paper
"I have changed my technique slightly after someone on Ukulele underground luthiers lounge…"
4 hours ago Knowledgebase Articles



© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->