Hi ther

I'm just building my first cigar box guitar, I have used kwila/merbau for the neck...... laminated 3 pieces, if I'm doing 25" is that from the front of the nut to the front of the bridge or is that measurement taken from the middle?.

built my own box 300mm long x 250mm wide and 80mm thick, used 12mm  MDF for the sides and good 4mm plywood for the top and bottom, going to stick a piezo under the lid.

had a bit of fun building it up, so I have another 2 on the go, I make my own boxes as cheap ones are hard to come by that are good size

Thanks Sid

Views: 105

Reply to This

Replies to This Discussion

Hi there

thanks for the reply, no I don't have a template, I'll just use one of the free online fret calculators, I'm  am used to working in mm so I have convert it all from inches to metric.

thanks for the link, looks as though its from the front of the nut, so I take it must be to the front of the bridge as well then

Easiest way to figure it out (well, for me anyway) - it's exactly at the point where the strings make contact with the bridge or nut. Depending on how each is cut, that could slightly vary from the "front" or "back." Just remember that the scale length is the length of the strings where they can vibrate freely. If you hold a rubber band, pinched between two sets of fingers, the scale length is that distance.

Cheers! Hope this helps!

thanks for the reply.

thats cool, when you look at like you said............... holding a rubber band, so yeh I'll make the nut and bridge and see where the strings fall on them, measure from there. Like you say they could vary a little.............................wont be much I suppose you just play with the bridge to make up for it.

good stuff

Sid

Yes, measure 25” from the middle of the nut where the strings touch to middle of the bridge? I like to center my nut & bridge at those measurements, works for me , no complaints. 
 If you scroll down on the link to the Scale Template, there’s measurements for 25” scale in metric?  cheers :)

hey thanks for that heads up on the metric measurements, I'll use that.

i find this online one the best.. http://www.ekips.org/tools/guitar/fretfind2d/

you can save a PDF of the scale and print it out..  only problem is you have to enable flash for this site as it needs it to show the save buttons.. 

you can specify number of strings ,number of frets, width at the nut as well as at the bridge and measurements to mm ..

theres alot of stuff out there, that I haven't seen heheh, just noticed about having flash installed, I'll have a look at this, looks good.

thanks for the link

You should be good if you’re not using an Apple/iOS format? 

I laid my frets out on aluminum yard/meter rulers with magic markers and scribed over the marker lines. Two scales per ruler.

A cheap econo/dollar store measuring tape is also good for making fret templates, they’re usually only about 6’ long, so you can plan out 2 full size necks on 1? Even the vinyl ones women use for sewing a great for templates, I’ve even seen Dar Stellabotta use one in her “How To” video? 

yeh I'll set a ruler out with fret markers for later builds I reckon, makes things easier in the long run

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

Fretwoods

Started by Brent Kasl in Building Secrets, Tips, Advice, Discussion. Last reply by Southpaw 19 hours ago. 4 Replies

Pickup Depth

Started by Brent Kasl in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans 21 hours ago. 1 Reply

How to Get Your Own Music on Spotify

Started by Shane Speal shanespeal.com in Feature Articles on Thursday. 0 Replies

Volume/Tone Pots

Started by Brent Kasl in Building Secrets, Tips, Advice, Discussion. Last reply by Paul Craig on Wednesday. 8 Replies

s/s lm386 draw amp,

Started by GARAGE HERMIT in Building Secrets, Tips, Advice, Discussion. Last reply by GARAGE HERMIT on Wednesday. 9 Replies

Nut milling

Started by Lothar Ahnert in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans on Wednesday. 3 Replies

Music

Loading…

© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->