Hi ther

I'm just building my first cigar box guitar, I have used kwila/merbau for the neck...... laminated 3 pieces, if I'm doing 25" is that from the front of the nut to the front of the bridge or is that measurement taken from the middle?.

built my own box 300mm long x 250mm wide and 80mm thick, used 12mm  MDF for the sides and good 4mm plywood for the top and bottom, going to stick a piezo under the lid.

had a bit of fun building it up, so I have another 2 on the go, I make my own boxes as cheap ones are hard to come by that are good size

Thanks Sid

Views: 99

Reply to This

Replies to This Discussion

Hi there

thanks for the reply, no I don't have a template, I'll just use one of the free online fret calculators, I'm  am used to working in mm so I have convert it all from inches to metric.

thanks for the link, looks as though its from the front of the nut, so I take it must be to the front of the bridge as well then

Easiest way to figure it out (well, for me anyway) - it's exactly at the point where the strings make contact with the bridge or nut. Depending on how each is cut, that could slightly vary from the "front" or "back." Just remember that the scale length is the length of the strings where they can vibrate freely. If you hold a rubber band, pinched between two sets of fingers, the scale length is that distance.

Cheers! Hope this helps!

thanks for the reply.

thats cool, when you look at like you said............... holding a rubber band, so yeh I'll make the nut and bridge and see where the strings fall on them, measure from there. Like you say they could vary a little.............................wont be much I suppose you just play with the bridge to make up for it.

good stuff


Yes, measure 25” from the middle of the nut where the strings touch to middle of the bridge? I like to center my nut & bridge at those measurements, works for me , no complaints. 
 If you scroll down on the link to the Scale Template, there’s measurements for 25” scale in metric?  cheers :)

hey thanks for that heads up on the metric measurements, I'll use that.

i find this online one the best.. http://www.ekips.org/tools/guitar/fretfind2d/

you can save a PDF of the scale and print it out..  only problem is you have to enable flash for this site as it needs it to show the save buttons.. 

you can specify number of strings ,number of frets, width at the nut as well as at the bridge and measurements to mm ..

theres alot of stuff out there, that I haven't seen heheh, just noticed about having flash installed, I'll have a look at this, looks good.

thanks for the link

You should be good if you’re not using an Apple/iOS format? 

I laid my frets out on aluminum yard/meter rulers with magic markers and scribed over the marker lines. Two scales per ruler.

A cheap econo/dollar store measuring tape is also good for making fret templates, they’re usually only about 6’ long, so you can plan out 2 full size necks on 1? Even the vinyl ones women use for sewing a great for templates, I’ve even seen Dar Stellabotta use one in her “How To” video? 

yeh I'll set a ruler out with fret markers for later builds I reckon, makes things easier in the long run


The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources


Volume/Tone Pots

Started by Brent Kasl in Building Secrets, Tips, Advice, Discussion. Last reply by Cause the Blue rat 6 hours ago. 4 Replies


Started by Shane Speal shanespeal.com in Feature Articles. Last reply by Alex Fong yesterday. 2 Replies

Mods to CBG kit

Started by James Pobog in Building Secrets, Tips, Advice, Discussion. Last reply by James Pobog on Wednesday. 4 Replies

s/s lm386 draw amp,

Started by GARAGE HERMIT in Building Secrets, Tips, Advice, Discussion. Last reply by Paul Craig on Wednesday. 8 Replies

Back Angle

Started by Brent Kasl in Building Secrets, Tips, Advice, Discussion. Last reply by Paul Craig on Monday. 4 Replies

Blog Posts

Mag pickup help

Posted by Fantacone Box Works on December 1, 2019 at 7:26pm 5 Comments

Tupelo Tenor kit

Posted by Craig W.Solomon on November 21, 2019 at 6:51pm 4 Comments

Hello from new member

Posted by Morgan L. Scoggins on November 16, 2019 at 9:52am 8 Comments

Latest Activity

Korrigan posted photos
9 minutes ago
John Grassens commented on John Grassens's photo

Aussie Resonator

"Thanks Jeff."
19 minutes ago
Doug Krantz posted a discussion

photos of old ukulele

Whilst talking to a gentleman at a music store the topic of cigarbox guitars came up.He told me his…See More
20 minutes ago
John Grassens and Jeff 'Bones' Reilly are now friends
20 minutes ago
Dave Lynas commented on Dave Lynas's photo

porcelain control knobs

"I’m loving the idea Bones. Another way to use clay on these guitars."
57 minutes ago
Dave Lynas commented on Dave Lynas's photo

the Omar Gang

"It would a few days Bones. This is tip o the iceberg. I can seem to stop making these things."
59 minutes ago
Dave Lynas commented on Dave Lynas's photo

Vern’s weird idea

"They are working out Bones. I’ve found several plastic knobs on eBay that will work great…"
1 hour ago
KOOL DOG HOOCH replied to KOOL DOG HOOCH's discussion HELP!! Going out of my flipping mind(intonation problem)
"I quickly glanced over This this morning and wasn't paying the attention it deserved. I always…"
1 hour ago
Dave Lynas commented on Dave Lynas's photo

Friday Night Special

"Duke pees where he wants Uncle. Don’t mess with The Duke..."
1 hour ago
Dave Lynas liked Uncle John's video
1 hour ago
Dave Lynas commented on Uncle John's video

Pawn Shop Christmas Commercial

"I’ll be right down Uncle. I got a huge load of diapers for Wishy Washy. Then I can use the…"
1 hour ago
Cause the Blue rat replied to Slowpaw Steve T's discussion CIGAR BOX NATION CHRISTMAS ALBUM 2019
"I have a second song in the works. When it's done I will send it to you first. If you decide…"
2 hours ago



© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->