Hello there!

Yesterday i discovered cigar box guitars and i was hooked immediately :). I started today with my build (a nice Free Cuba box i found years ago) and due to my inexperience and the difference between the box in the tutorials and my box, i made some errors. I didn't think about the need of a seamless transition between box and neck. I attached some pictures so you can see.

Because of the big lid, there's quite a gap between the neck and the box. Could i just glue another piece with the remaining height on top of my neck? Maybe also take some wood from the bottom of the neck to make it less bulky?

In addition, there's a gap inside the box between the neck piece and the top of the lid (around 1.4cm/0.55 inches). I've read that you can glue the neck and the box together or leave a little space, but that amount of space would be too much probably? So should I glue a piece on the neck inside to touch/come closer to the top of the lid? Would it be able to resonate properly? Or should I discard this project and start over with a new box?

Im sorry for asking this many questions, I'm just a little frustrated right now. I hope you can understand my problems.

Thanks in advance,

Toby

Views: 225

Attachments:

Reply to This

Replies to This Discussion

Here’s a video of how to better prepare your neck for the box

https://m.youtube.com/watch?v=2W6A38lMgJ0&list=PLQoYJG1ht92f3gc...

Welcome to CGB addiction. Don't be discouraged with your first build. There "WILL" be more. Use this one as a good learning experience.

Now to the current build. You "could" add a piece of wood on top of your existing neck to make it flush (or about 1/4" higher than the box lid, but I wouldn't. It's gonna look weird, weight too much and be a pain in the ass to play.

Instead, consider notching the box lid so the neck rest against the top-inside of the lid. then, notch the neck where it goes inside the box by about 1/4". That will raise the neck, when installed, to slightly above the top (outside) of the box. Look at photos of cigar box guitars on this site and you'll see what I'm talking about.

Now, there will now be an opening in the side of the box below the neck since the neck has been raised up. use a piece of wood (the slide in liners of a cigar box would work well) to build a nice looking neck surround that hides the hole.

You should now be close to a normal cigar box guitar. Work toward building it right instead of compensating for problems and you'll have a playable guitar.

Do some YouTube searches of building CBGs and you will find lots of helpful vids.

Good luck

Hi Toby and welcome, my first advise, and its what I do is not to glue my necks in, but to screw or bolt, easy if you have a lid that removes easily. Makes it easier to learn the tricks of setting up, I think. 

Also as the top is the most important component in the acoustic sound chain, so don't dampen its vibrations by having it touching anything in side, except maybe a brace if needed. 

Here's a few photo's of what I have done in the past. Left a few steps out but you should get the idea.

Taffy,

The method to attach a neck to a cigar box you've shared here is a terrific idea.

I'm embarrassed to say that putting neck mounting blocks on the outside of the box simply has never crossed my mind.

In the past I've struggled with quiet CBGs due, in part, to the sound chamber filled with too much wood.

I really dig the solution you've shared for that issue and look forward to trying it. Awesome stuff, man.

If you try this on  your box, Toby, I hope you post pictures of the results. 

And of course, welcome to the cigar box guitar community, Toby. You're gonna love it.

Thanks for all the helpful replies! Im definitely encouraged to fix my build and have ideas for the next box guitar. Great community :)
Thanks for the detailed reply. Didn't think of this but this looks like the best solution :)

Hi again, I rarely do a neck through, I mainly do as shown in the photo.

Two blocks. One inside [neck block] and another out side [ the heal], this increases the gluing area or in my case the bolting/screwing area.

Also allows for more air space in the box cos' no neck shaft. 

Cheers Taff

Awesome design. on another blog i was going on about thru necks, but mentioned any thought out design works. This is a great example, very nicely built. Actually a setup like this takes more time and patience than putting the neck through anyway. Wood glue is truly an amazing thing, what they say about a good glue joint being stronger than the wood is true.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

Busking Tunes

Started by Donovan in Performances, How to Play, Lessons, Concerts. Last reply by Will "KOOL DOG HOOCH" Bonner 14 hours ago. 3 Replies

PDF DOWNLOAD: How to Build a Hurdy Gurdy

Started by Shane Speal shanespeal.com in Feature Articles. Last reply by Philip Taylor on Thursday. 8 Replies

Pitch Pine

Started by Laurence Owen in Building Secrets, Tips, Advice, Discussion. Last reply by Laurence Owen on Thursday. 4 Replies

Samantha Fish oil can guitar

Started by Kurt Reifert in Building Secrets, Tips, Advice, Discussion. Last reply by Bruno Ballardini on Wednesday. 5 Replies

"Another' lid question.

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner on Wednesday. 10 Replies

Pickup placing

Started by micky rooney in Performances, How to Play, Lessons, Concerts. Last reply by micky rooney on Tuesday. 9 Replies

Blog Posts

Mama Pearson's Soaporium

Posted by Rick Tish on September 14, 2019 at 8:52pm 0 Comments

Fresh Diddley Bow- "Why Not?"

Posted by Glenn Kaiser on September 13, 2019 at 10:23pm 1 Comment

Good weekend selling

Posted by Rick Tish on September 11, 2019 at 10:13pm 0 Comments

Cigar Box Guitar Music - Old time Blues

Posted by John on September 9, 2019 at 6:00pm 2 Comments

The Accidental Canjo

Posted by Poorness Studios on September 8, 2019 at 10:30am 2 Comments

Latest Activity

Andries D. EKER commented on Andries D. EKER's video
Thumbnail

Never Big on Ego A D Eker 2019

"Hi there Dennis "Denbo", appriciate the like  ! Thanks !"
59 minutes ago
Bob "Ambrose" Negus liked HOLLOWBELLY's video
2 hours ago
Bob "Ambrose" Negus commented on HOLLOWBELLY's video
Thumbnail

HOLLOWBELLY LIVE at Dark Holler Festival 2019 Back on the Ward.

"Crackin' performance... Keep coming back!"
2 hours ago
Bob "Ambrose" Negus commented on Uncle John's video
Thumbnail

Weeping Willow Blues

"That's a fine looking box, front and back Unc J.  Sounds great combined with the…"
2 hours ago
Bob "Ambrose" Negus liked Uncle John's video
2 hours ago
Bob "Ambrose" Negus liked High Bird Handcrafted Instuments's photo
2 hours ago
Bob "Ambrose" Negus liked High Bird Handcrafted Instuments's photo
2 hours ago
Bob "Ambrose" Negus liked High Bird Handcrafted Instuments's photo
2 hours ago
Dave Lynas commented on BUGGY (C)'s video
Thumbnail

A Jug Band Tester

"Great Jug Band tribute Buggy. I love those old photos and films. You showed the best. Thanks Buggy."
2 hours ago
Dave Lynas commented on Anthony Insetta's video
Thumbnail

1927 Martin 2-17

"Wow Anthony. You have the best. Nice of you to share a play for us to hear. Thanks friend."
2 hours ago
Dave Lynas liked Anthony Insetta's video
3 hours ago
Dave Lynas commented on Dave Lynas's video
Thumbnail

Cooking Leftovers

"Thanks Denbo. Today we are going up very early to take advantage of a cool morning. Hopefully the…"
3 hours ago

Music

Loading…

© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->