Hello there!

Yesterday i discovered cigar box guitars and i was hooked immediately :). I started today with my build (a nice Free Cuba box i found years ago) and due to my inexperience and the difference between the box in the tutorials and my box, i made some errors. I didn't think about the need of a seamless transition between box and neck. I attached some pictures so you can see.

Because of the big lid, there's quite a gap between the neck and the box. Could i just glue another piece with the remaining height on top of my neck? Maybe also take some wood from the bottom of the neck to make it less bulky?

In addition, there's a gap inside the box between the neck piece and the top of the lid (around 1.4cm/0.55 inches). I've read that you can glue the neck and the box together or leave a little space, but that amount of space would be too much probably? So should I glue a piece on the neck inside to touch/come closer to the top of the lid? Would it be able to resonate properly? Or should I discard this project and start over with a new box?

Im sorry for asking this many questions, I'm just a little frustrated right now. I hope you can understand my problems.

Thanks in advance,

Toby

Views: 210

Attachments:

Reply to This

Replies to This Discussion

Here’s a video of how to better prepare your neck for the box

https://m.youtube.com/watch?v=2W6A38lMgJ0&list=PLQoYJG1ht92f3gc...

Welcome to CGB addiction. Don't be discouraged with your first build. There "WILL" be more. Use this one as a good learning experience.

Now to the current build. You "could" add a piece of wood on top of your existing neck to make it flush (or about 1/4" higher than the box lid, but I wouldn't. It's gonna look weird, weight too much and be a pain in the ass to play.

Instead, consider notching the box lid so the neck rest against the top-inside of the lid. then, notch the neck where it goes inside the box by about 1/4". That will raise the neck, when installed, to slightly above the top (outside) of the box. Look at photos of cigar box guitars on this site and you'll see what I'm talking about.

Now, there will now be an opening in the side of the box below the neck since the neck has been raised up. use a piece of wood (the slide in liners of a cigar box would work well) to build a nice looking neck surround that hides the hole.

You should now be close to a normal cigar box guitar. Work toward building it right instead of compensating for problems and you'll have a playable guitar.

Do some YouTube searches of building CBGs and you will find lots of helpful vids.

Good luck

Hi Toby and welcome, my first advise, and its what I do is not to glue my necks in, but to screw or bolt, easy if you have a lid that removes easily. Makes it easier to learn the tricks of setting up, I think. 

Also as the top is the most important component in the acoustic sound chain, so don't dampen its vibrations by having it touching anything in side, except maybe a brace if needed. 

Here's a few photo's of what I have done in the past. Left a few steps out but you should get the idea.

Taffy,

The method to attach a neck to a cigar box you've shared here is a terrific idea.

I'm embarrassed to say that putting neck mounting blocks on the outside of the box simply has never crossed my mind.

In the past I've struggled with quiet CBGs due, in part, to the sound chamber filled with too much wood.

I really dig the solution you've shared for that issue and look forward to trying it. Awesome stuff, man.

If you try this on  your box, Toby, I hope you post pictures of the results. 

And of course, welcome to the cigar box guitar community, Toby. You're gonna love it.

Thanks for all the helpful replies! Im definitely encouraged to fix my build and have ideas for the next box guitar. Great community :)
Thanks for the detailed reply. Didn't think of this but this looks like the best solution :)

Hi again, I rarely do a neck through, I mainly do as shown in the photo.

Two blocks. One inside [neck block] and another out side [ the heal], this increases the gluing area or in my case the bolting/screwing area.

Also allows for more air space in the box cos' no neck shaft. 

Cheers Taff

Awesome design. on another blog i was going on about thru necks, but mentioned any thought out design works. This is a great example, very nicely built. Actually a setup like this takes more time and patience than putting the neck through anyway. Wood glue is truly an amazing thing, what they say about a good glue joint being stronger than the wood is true.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

Fretless cbg

Started by Caleb D Bennett in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans 13 hours ago. 3 Replies

We build guitars

Started by Wal Callaby in Other stuff - off topic, fun stuff, whatever. Last reply by Jerry Jordan 14 hours ago. 17 Replies

Open Gear Tuners

Started by Brent Kasl in Building Secrets, Tips, Advice, Discussion. Last reply by Jerry Jordan 18 hours ago. 9 Replies

One Finger Lesson: Take Me Home Country Roads - VIDEO & TAB

Started by Shane Speal shanespeal.com in Feature Articles. Last reply by Chuck otto 19 hours ago. 2 Replies

Box fiddle #1

Started by Gervase Gallant in Building Secrets, Tips, Advice, Discussion. Last reply by Gervase Gallant yesterday. 6 Replies

Nut and #1 fret spacing.

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner on Monday. 2 Replies

Zero fret/nut idea

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner on Sunday. 8 Replies

Rescued ss can.

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner on Saturday. 15 Replies

Looking for Builders and Players in Florida!

Started by Will "KOOL DOG HOOCH" Bonner in Fests and Concerts: Organizing and Promoting. Last reply by Will "KOOL DOG HOOCH" Bonner on Thursday. 15 Replies

Fun with a 2x4 Bass - Build Your Own

Started by Shane Speal shanespeal.com in Feature Articles. Last reply by Mike Parker on Thursday. 24 Replies

Blog Posts

A Tale of Two Ukes

Posted by Poorness Studios on June 25, 2019 at 10:00am 1 Comment

Adventures in headstock-making

Posted by Sean Murphy on June 15, 2019 at 4:41pm 2 Comments

site bugs

Posted by the anonymous pick on June 13, 2019 at 8:05pm 6 Comments

Cheesecake Banjolele

Posted by James Matthews on May 21, 2019 at 7:14pm 3 Comments

Latest Activity

Dave Lynas commented on Dave Lynas's photo
Thumbnail

2 string Fiddles

"Thanks Bones, AGP, Poorness. I love the old boxes. Like fruit crates, they have great lettering and…"
1 hour ago
Jeff 'Bones' Reilly commented on Dave Lynas's photo
Thumbnail

2 string Fiddles

"Loving the ok box to cool Dave . "
3 hours ago
Jeff 'Bones' Reilly liked Dave Lynas's photo
3 hours ago
Dennis "Denbo" Goodinson liked Randy S. Bretz's photo
4 hours ago
Dennis "Denbo" Goodinson liked Randy S. Bretz's photo
4 hours ago
the anonymous pick commented on Ricky's photo
5 hours ago
Wekasper updated their profile
5 hours ago
Lonman commented on Cigarbox Slim's photo
Thumbnail

New Resonator

"real nice.  good job on the tin"
7 hours ago
Lonman posted a photo

first bass guitar

my first bass guitar went to its owner tonight. I enjoyed making this. I was perturbed that the CB…
8 hours ago
Mauricio Twelve commented on AGP #'s video
Thumbnail

AGP #356 ''LOWDM'' Paris Texas 25 May 2019

"Linda interpretação com melodia que me faz fechar os olhos e viajar pela…"
8 hours ago
Mauricio Twelve liked AGP #'s video
8 hours ago
Richard Sundberg commented on Richard Sundberg's video
Thumbnail

Hopeless. By George Jones Jr. with Richard Sundberg

"I’m just a studio musician haha! ! This is an outstanding song written and played, and sung…"
10 hours ago

Music

Loading…

© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->