Hello there!

Yesterday i discovered cigar box guitars and i was hooked immediately :). I started today with my build (a nice Free Cuba box i found years ago) and due to my inexperience and the difference between the box in the tutorials and my box, i made some errors. I didn't think about the need of a seamless transition between box and neck. I attached some pictures so you can see.

Because of the big lid, there's quite a gap between the neck and the box. Could i just glue another piece with the remaining height on top of my neck? Maybe also take some wood from the bottom of the neck to make it less bulky?

In addition, there's a gap inside the box between the neck piece and the top of the lid (around 1.4cm/0.55 inches). I've read that you can glue the neck and the box together or leave a little space, but that amount of space would be too much probably? So should I glue a piece on the neck inside to touch/come closer to the top of the lid? Would it be able to resonate properly? Or should I discard this project and start over with a new box?

Im sorry for asking this many questions, I'm just a little frustrated right now. I hope you can understand my problems.

Thanks in advance,

Toby

Views: 215

Attachments:

Reply to This

Replies to This Discussion

Here’s a video of how to better prepare your neck for the box

https://m.youtube.com/watch?v=2W6A38lMgJ0&list=PLQoYJG1ht92f3gc...

Welcome to CGB addiction. Don't be discouraged with your first build. There "WILL" be more. Use this one as a good learning experience.

Now to the current build. You "could" add a piece of wood on top of your existing neck to make it flush (or about 1/4" higher than the box lid, but I wouldn't. It's gonna look weird, weight too much and be a pain in the ass to play.

Instead, consider notching the box lid so the neck rest against the top-inside of the lid. then, notch the neck where it goes inside the box by about 1/4". That will raise the neck, when installed, to slightly above the top (outside) of the box. Look at photos of cigar box guitars on this site and you'll see what I'm talking about.

Now, there will now be an opening in the side of the box below the neck since the neck has been raised up. use a piece of wood (the slide in liners of a cigar box would work well) to build a nice looking neck surround that hides the hole.

You should now be close to a normal cigar box guitar. Work toward building it right instead of compensating for problems and you'll have a playable guitar.

Do some YouTube searches of building CBGs and you will find lots of helpful vids.

Good luck

Hi Toby and welcome, my first advise, and its what I do is not to glue my necks in, but to screw or bolt, easy if you have a lid that removes easily. Makes it easier to learn the tricks of setting up, I think. 

Also as the top is the most important component in the acoustic sound chain, so don't dampen its vibrations by having it touching anything in side, except maybe a brace if needed. 

Here's a few photo's of what I have done in the past. Left a few steps out but you should get the idea.

Taffy,

The method to attach a neck to a cigar box you've shared here is a terrific idea.

I'm embarrassed to say that putting neck mounting blocks on the outside of the box simply has never crossed my mind.

In the past I've struggled with quiet CBGs due, in part, to the sound chamber filled with too much wood.

I really dig the solution you've shared for that issue and look forward to trying it. Awesome stuff, man.

If you try this on  your box, Toby, I hope you post pictures of the results. 

And of course, welcome to the cigar box guitar community, Toby. You're gonna love it.

Thanks for all the helpful replies! Im definitely encouraged to fix my build and have ideas for the next box guitar. Great community :)
Thanks for the detailed reply. Didn't think of this but this looks like the best solution :)

Hi again, I rarely do a neck through, I mainly do as shown in the photo.

Two blocks. One inside [neck block] and another out side [ the heal], this increases the gluing area or in my case the bolting/screwing area.

Also allows for more air space in the box cos' no neck shaft. 

Cheers Taff

Awesome design. on another blog i was going on about thru necks, but mentioned any thought out design works. This is a great example, very nicely built. Actually a setup like this takes more time and patience than putting the neck through anyway. Wood glue is truly an amazing thing, what they say about a good glue joint being stronger than the wood is true.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

Frets and fretboard

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by Jerry Jordan 13 hours ago. 9 Replies

Perma grit sandpaper

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner yesterday. 4 Replies

Fret Sides Dressing

Started by Brent Kasl in Building Secrets, Tips, Advice, Discussion. Last reply by Titch the Clown on Friday. 8 Replies

Slide off decals

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner on Friday. 10 Replies

30.5" scale lay-out help needed please!

Started by Will "KOOL DOG HOOCH" Bonner in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner on Thursday. 20 Replies

Break angle for bridge

Started by Fantacone Box Works in Building Secrets, Tips, Advice, Discussion. Last reply by Will "KOOL DOG HOOCH" Bonner on Thursday. 28 Replies

Navigating this forum

Started by Fantacone Box Works in Performances, How to Play, Lessons, Concerts. Last reply by Fantacone Box Works Jul 14. 5 Replies

Blog Posts

Getting ready for next build

Posted by Sean Murphy on July 17, 2019 at 12:54pm 2 Comments

What wood is this?

Posted by Sean Murphy on July 16, 2019 at 10:48am 7 Comments

apology

Posted by Danny Gordon on July 13, 2019 at 7:30pm 3 Comments

Latest Activity

Will "KOOL DOG HOOCH" Bonner commented on Sean Murphy's blog post Getting ready for next build
"Nice,  don't forget to post a vid of what it sounds like. "The proof is in the…"
1 hour ago
Beetlejuice! posted photos
1 hour ago
the anonymous pick commented on Evan Keeling's photo
3 hours ago
the anonymous pick commented on Poorness Studios's photo
3 hours ago
Lonman commented on Rich's photo
Thumbnail

RTL TinBG Collection1

"like 'em all, especially the boom box.  "
4 hours ago
Lonman commented on Rich's photo
Thumbnail

RTL Tinbox Batman Head stock rear view

"Holey Headstock! Nice job.  I did not think of that on the batman tool tin 3 string I made…"
4 hours ago
Lonman replied to Paul Craig's discussion What's on your workbench?
"thanks for the tips Kigar. Looking forward to giving it a try"
4 hours ago
Dave Lynas commented on Dave Lynas's video
Thumbnail

Waltz of the Scarecrows

"Some leaves falling and yellow. High Summer. Lightning bugs and flocking robins Nancy. I love it…"
4 hours ago
Clint Spotts posted a photo
7 hours ago
Clint Spotts commented on Beetlejuice!'s photo
Thumbnail

- One String Sam -

"This is bad-ass! Captain Beefheart said One String Sam’s “I Need a $100” is like…"
8 hours ago
Clint Spotts liked Beetlejuice!'s photo
8 hours ago
Uncle John commented on Uncle John's video
Thumbnail

Gospel with Landfill Lorretta & Iowa Saxophone

"That IS a sweet baby with a smile.  :}"
8 hours ago

Music

Loading…

© 2019   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->