Well I finished my first a couple of days ago.  Fretless Acoustic.  Learned a lot and getting ready to start

my second.  Sounds good!  On these type of boxes is there a latch or something that

I can get to keep the lid fastened?  

Views: 107

Attachments:

Reply to This

Replies to This Discussion

I usually build a post or two to screw the lid down, if it doesn't already have a latch. I've thought of putting a couple of strong magnets into posts on the inside that would face each other to magnetically hold it closed, but haven't tried it yet. I'm guessing there might be some problems with that design due to buzzing from the vibration. Might try that my next build.

Also, congrats on the build!

Huh! Good idea. I guess you glue a post on the inside of the box and make the height of the post just right to use velcro attached to top of post and the inside top of the box........

i wouldnt recomend velcro. it would deaden the top and not let it vibrate. probably ok on a electric only build.

on another note, have a look at pictures of other acoustic CBG's bridge placement and gret for ideas to " inspire you" , pinch that is...lol

Either gluing it down or screwing it down is the best, a loose lid will bring unwanted buzz?

Timothy,

I followed the Gitty Basic Plan (Glenn Watts) and that's the way it's setup on bridge placement based on 31" of neck material length. Realize it's not ideal and the bridge should be moved more towards the center of box a little.  Just didn't want to deviate from plan on the first one.

Thanks on the velcro. I think you're correct, probably would dampen vibration of the top. Will look for another way. The reason the neck falls open just a tad when playing is that I made a "test" neck first using pine and cut the cigar box notches based on that and it fit perfectly. Made a new neck with Poplar and the width of the board was a slight bit under 1.5" so I ended up with some "play" between the neck and the box. Was thinking I could probably come up with some type of "shim" that you can't see to tighten the connection and that would solve the problem.

Thanks again,
Mark

The Missus got these for me to hold down and decorate the corners. not sure where she got them she does a lot of scrap booking etc and probably cant rmemeber herself..lol

Timothy those are pretty sporty looking. Would look great on a box!

On latching down the top. I had some maple veneer that I thinned down and used
as shims for the small gap between the neck and the box. Stained them to match the stain I used on the neck and placed a drop of thin CA Glue to anchor them in place.
Worked great! Box is now tightly closed up.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources


Forum

Discussion: Toothpick Frets?

Started by Habanera Hal in Feature Articles. Last reply by Paul 2 hours ago. 26 Replies

Fret calculations

Started by Graham Wedepohl in Building Secrets, Tips, Advice, Discussion. Last reply by BrianQ. on Saturday. 5 Replies

Upright Ubass

Started by Titch the Clown in Building Secrets, Tips, Advice, Discussion. Last reply by Greg Potts Jun 20. 1 Reply

New here

Started by Clarence johnson in Performances, How to Play, Lessons, Concerts. Last reply by Road Rash Roy Jun 18. 13 Replies

Latest Activity

AGP # commented on AGP #'s photo
Thumbnail

AGP #77 - "Pokeher" Modification

""Thanks Bob & RTZ", and yes RTZ, some earlier builds can always do with a…"
1 hour ago
AGP # commented on AGP #'s photo
Thumbnail

AGP #77 - "Pokeher" Modification

""Thanks Doug", Yep!, the original Bridge was a bit ordinary, and used wander around a…"
1 hour ago
AGP # commented on AGP #'s photo
Thumbnail

AGP #77 - "Pokeher" Modification

""Thanks UJ", the main reason for the revisit was to fix the saggy bridge problem, because…"
1 hour ago
AGP # commented on AGP #'s photo
Thumbnail

AGP #77 - "Pokeher" Modification

""Thanks Rope", the Vol, Tone & Headstock Chips are the Spicy Ones, not sure if its…"
1 hour ago
RTZGUITARS commented on BUGGY (C)'s video
Thumbnail

Dark

"nicely done more rockin then dark"
2 hours ago
the anonymous pick posted photos
2 hours ago
RTZGUITARS commented on Dave Lynas's photo
Thumbnail

Wood Stock

"Boxelder tree"
2 hours ago
RTZGUITARS commented on Poorness Studios's video
Thumbnail

The Lion Sleeps Tonight (performed on homemade instruments)

"Jugg bands are  in around here, well done.  "
2 hours ago
RTZGUITARS commented on A.D.EKER's video
Thumbnail

Monkey see Monkey do BCB Jugg Band 2021

"Hahahahaha Monkey Jugg band everything but a slide whistle"
2 hours ago
RTZGUITARS commented on AGP #'s photo
Thumbnail

AGP #77 - "Pokeher" Modification

"Nice, some build are just never done"
2 hours ago
RTZGUITARS commented on Uncle John's video
Thumbnail

Cigar Box Gospel ~ Soon & Very Soon

"I feel better thanks John,  Is that a Church tuning?"
2 hours ago
Paul replied to Habanera Hal's discussion Discussion: Toothpick Frets?
"I have used toothpicks on a few canjos. After gluing them in my sawed slots on the fretboard , I…"
2 hours ago

Music

© 2021   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->