I am adding a piezo pickup from CB Gitty to a new build. I understand they can be hot sounding when not shielded, which brings me to my question. If I were to make my own disc-o-tone, are both sides of the piezo covered in wood? If not, should the brass disc or the ceramic disc face the soundboard?

Many thanks!

Views: 604

Reply to This

Replies to This Discussion

Oh, I should have included a link to what I am thinking about making:

Both sides are embeeded in wood, although the wire side appears to be cork on the Amazon.com pictures.  I don't think it will matter much which faces the soundboard, but you might experiment both ways.  It will be more important that you have the disc tightly and evenly laminated within the wood case, which I suppose is one of the reasons why there's cork on the back side.

Of course, CB Gitty has done a bunch of the trial and error for you already. Might be worth just paying the few extra bucks for the prewired set up with volume control.

I probably would have just picked one up from CBGitty had I realized, but I am new to CBGs and new to pickups. Cork and craft foam happen to be both on hand, so I will do a little fiddling around. Thanks for the help!

There are a bunch of ways that piezos are used.  Some just embed them in a gob of hot glue, some potted in bottle caps with silicone, some just foam double side tape to the soundboard (I've done this one).  I remember someone just wrapping the disc in tissue or cotton rag and leaving it loose in the box.

if the piezo is sandwiched in wood, it probably doesn't make any difference it's orientation vis-a-vis the soundboard.  If it is embedded in wood with only one side exposed, I would definitely orient the the brass toward the wood (away from the soundboard).  I've build plenty of "martin style" bridges, with piezo embedded brass side toward the void on the underside of the bridge.  before gluing the bridge in place, I cover the ceramic side with silicone caulk.  the arrangement cuts out feedback and lessen top noise.

The disco-tone from CB gitty is embedded in a hardwood that looks like oak, but Bad Finger is right that the wire side is cork.  From what I can see on the one that I have, there is some sort of silicone or hot glue buffer between the actual piezo and the cork and I would imagine it's is covering the entire piezo.  The instructions tell you to put the hardwood surface on the underside of the sound board near the bass side of the bridge (so corkside down).  The hardwood has double sided tape already attatched to it to affix to the sound board. 


As mentioned below, CB Gitty has probably done a lot of experimenting and the time attempting to replicate this will likely not be worth the extra few dollars.  

Thanks to everyone for the advice. I agree about CBGitty having done trouble-shooting. However, I had already purchased from them a piezo pickup kit, then discovered they should be shielded to dampen the treble tones.

I will post the results later. Thanks again!
The piezo is shielded with hardwood, foam, and foam mounting tape. It sounds great, except I am having a bit of a problem with a volume control. I am happy with the pickup arrangement, though.

Piezo elements have a really high impedance, like near 1M ohm.  Using a small pot won't work, you need to use one that is at least 250k, if I recall... it's around here somewhere.  

Your best bet is to use a buffer/booster and set the volume there.  You could install a 9V buffer IN your CBG, if you know a little electronics.  Google Jfet preamp.


The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources


Cigar Box Amp Mods

Started by Cigar Box Nation in Feature Articles. Last reply by RTZGUITARS on Friday. 14 Replies

Blog Posts

Mr. Bells

Posted by Stephen Cohen on September 4, 2021 at 12:30pm 0 Comments

Bookie's Poor Man's Dobro

Posted by Steve Bookout on July 18, 2021 at 2:04pm 4 Comments

Get your groove on for free

Posted by François on July 13, 2021 at 3:05pm 1 Comment

Latest Activity

Giuseppe Cassa commented on Giuseppe Cassa's photo

Trunk Bass

"@Tom Hoglund well i found an old electric doublebass neck, it was all worm-eaten and the…"
8 minutes ago
the anonymous pick commented on the anonymous pick's photo

swamp witch guitar bubble gum 5

"Cheers UJ I have your guit by the front door ,  most visitors  sample it and comment on…"
55 minutes ago
the anonymous pick commented on the anonymous pick's photo

swamp witch guitar bubble gum 4

"Thanks Unk ,  yup , pretty much the regular swamp witch sound , but a shorter scale (due to…"
58 minutes ago
Steebos Kalist commented on Steebos Kalist's video

Life By The Drop - Cigar Box Guitar Cover

""Thanks everybody! Letting it all hang out is something I'm becoming more comfortable…"
1 hour ago
Gary O'slide posted videos
2 hours ago
Uncle John commented on Rich's photo

Padron 4 hole front

"You folks that build all by hand tools put extra soul, sweat and sometimes blood into your…"
3 hours ago
Rich commented on Rich's photo

Padron 4 hole whole

"Thanks for the likes, Keith and Brian.  UJ and Doug - I appreciate your opinions."
3 hours ago
Rich commented on Rich's photo

Padron 4 hole front

"who's Dave? I only saw Doug."
3 hours ago
Rich commented on Rich's photo

Padron 4 hole head stock back

"Yeah, Doug.... and it's more obvious with this 1950s record cover."
3 hours ago
Rich commented on Rich's photo

RTL Fret markers - Commercial Sign Vinyl

"I also rub the wood with alcohol just before applying the vinyl. I then use Howards wax and feed…"
3 hours ago
Rich commented on Rich's photo

Padron 4 hole front

"Thank you , Dave and UJ     The slightly katty-wampus look of the final oval is because I…"
3 hours ago
Profile IconEdward J Weller, William, William McGlashan and 3 more joined Cigar Box Nation
3 hours ago


© 2021   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->