My sister gave me 3, '58 Corvette Wheel Covers. I was going to make a 2 1/2" round Walnut skirt. I was attempting to kerf cut and soak in hot bath water to get the bend. I started off all wrong the saw kerfs would show outside the outermost edge. On top of that I figured my board length too short. I am making a steam chamber to bend. I am also going to make a form. Made a 10 ft. round table for the rotunda of a building once and it was a piece of cake compared to trying to get this tight bend Learned a bunch but got nothing to show for it.  When I took my diameter, I took it to ring that grabs rim. It should have been  1/8" or so past the outermost lip.

      I intend for the strings to come out the base of the flipper. Bridge is going to be on flat ring just outside flipper. Picking area will be in the fluted dish area.I have rotated flipper 1/4 turn (as shown) so valve stem can come out hole Long screw through the middle  to catch neck board where valve would be. Chrome skull to cover screw head, looking like valve stem cover. That is what my head is saying, now I need to get my hands to cooperate.

Views: 449

Attachments:

Reply to This

Replies to This Discussion

Good Luck, it looks ambitious.

I have done a pretty tight radius bend with walnut before. Didn't use kerf method insted palnned to 1/8 thickness, soaked in very hot water for about an hour and bent around a form. I think this will work for your situation.

      I think you and I are on the same page. I am going to use 1/4" plywood for substrate and laminate the 1/8" walnut over the top.II don't have a planer, but when I had use of one I always found thin stuff was problematic.I can re-saw up to 2 1/2" on tired old table saw.I have ordered a steam generator and am going to make a steam chamber out of a 5ft' section of 8" and 6^' diameter galvanized heat duct and a couple cans of spray foam insulation.It will come in handy later for this habit I got.Bent wood on gits is common enough.I might be able to sell rings for hub cap gits. After all i will have to make bending form. Will be good for Chevy 15" rims. Trying to bend using 1/4" nylon or web clamp is a problem. What happens is it starts to bend at it's weakest point and wants to continue to bend there and isn't consistent..I will keep ya" posted.

     

This is a very interesting post. I don't know very much about forming wood in this way but I have some questions.
What kind of working time do you have after you give the wood a hot water bath?
When cutting the wood to join the ends, do you do it before you bath the wood, or after it has dried? Is it a butt joint or angled?
What kinds of wood are best for hot water method? Do different kinds of wood require longer time in bath?
Can you use strap clamps to hold the wood against the form while it is drying?
Sorry for so many questions, but I tried something like this with a student in the past year that didn't work out too well and this post reminded me of it. We were using balsa and I wasn't able to heat the wood enough and probably not long enough. It couldn't get in a tight enough area, kept cracking... We ended up using the wood cross grain and it worked better.

      Greg, I don't know anything about forming wood either. Keep in mind part of the title of the OP was Epic Fail!. I will tell you what does work. I once trained a 3/8" dowel rod around a broom handle so as to make a snake that I could woodburn. That worked got 2 1/2 turns, to make a walking stick. Accuracy wasn't a problem. I ran a tub full enough to submerge (weighted down).

      Now as far as joint, I mitered my the 3 of the bent pieces I showed in the tub. I let the things soak for about 2 hours and started tightening the nylon cord you see them wrapped. The problem is you have no control over the bend. It starts bending in the weakest place and wants to bend more there than the rest of the radius. I broke one got one to make the bend and clamped it ready for glue up. I miscalculated the diameter so the wheel cover was too big for my trouble. Threw the other one in the boo boo pile for later. Look at the "How its Made" episode that JL linked. That will give you a better description than I can. Good Luck.

     

Going to reply to my reply bc I left out the fact that you bend a little, let soak, bend some more, run more hot water in tub. Let soak bend some more. Every time you go to the can bend a little more. Takes about a day or so. This isn't a production deal. Good for one off.

maybe this "how its made" will give you some ideas...

https://www.youtube.com/watch?v=uDsxFTIhAk0

      JL, thanks for that one. I really appreciate your help there. I had already figured on steam bending. I was going to miter the pieces but that tapered lap joint they did is the way to go. I think the same jig I use to make scarf joints on my table saw may work to make joint for git body.The neck of the guitar will hide the joint in the builds, but the surface area of the glue line in the snare drum is way stronger than a miter. I have fabricated a steam chamber and got a steam generator. I am into it $100 +/-,right now. I am going to make a form the size of the WC so it will be uniform shape and dimension. Also it will make a glue jig. I need 3 good ones, not 300, so it will probably work. The steam chamber is 1 each 8" & 6" galvanized heat duct with 2 each 6" starters. 2 16 oz cans of spray foam insulation. I also have some 1/2" Styrofoam like you insulate exterior walls.The formula is 15 min. of steam for each 1/4" of thickness. They say kiln dried lumber won't bend. Mine is air dried in my basement for the last 25 years. Had an ol' B-I-L in W. Va. that ran a one man saw mill that gave me a bunch of stuff. I am just guessing, but i say if you soak kiln dried lumber overnight in a bathtub, it will bend. Wood is like a dried out kitchen sponge. Dry, no bend,slightly damp bend a little,wet bend all you want. Steam alone won't penetrate the cellular structure. That is opinion only but I didn't just fall off the turnip truck  (;-D)

Attachments:

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor


Recommended Links & Resources


Forum

Cigar Box Amp Mods

Started by Cigar Box Nation in Feature Articles. Last reply by RTZGUITARS yesterday. 14 Replies

Blog Posts

Mr. Bells

Posted by Stephen Cohen on September 4, 2021 at 12:30pm 0 Comments

Bookie's Poor Man's Dobro

Posted by Steve Bookout on July 18, 2021 at 2:04pm 3 Comments

Get your groove on for free

Posted by François on July 13, 2021 at 3:05pm 1 Comment

Latest Activity

Doug Thorsvik posted a video

Beer Barrel Polka: 3-string (G1G2D3) Cigar Box Guitar

Cigar Box Guitar Slingers - Spokane, 73rd Zoom Mtg Sep 13, 2021. More info and free songbooks: https://sites.google.com/site/cigarboxguitarslingersspokane/home
13 minutes ago
bemuzic commented on bemuzic's video
Thumbnail

Busking, St Ives w 3 String Cigar Box Guitar - Magic Paints, with dancing children :-)

"thanks Brian and Doug, yep a few good minutes of connecting with people through music  and…"
14 minutes ago
Doug Thorsvik commented on bemuzic's video
Thumbnail

Busking, St Ives w 3 String Cigar Box Guitar - Magic Paints, with dancing children :-)

"It’s always fun to see children respond to music. So unselfconscious and authentic. Thanks…"
18 minutes ago
Doug Thorsvik commented on Jim Morris's video
Thumbnail

For Dave

"Heartfelt tribute Jim! A beautiful reminder of how Dave influenced us here at CBN."
27 minutes ago
BrianQ. commented on bemuzic's video
Thumbnail

Busking, St Ives w 3 String Cigar Box Guitar - Magic Paints, with dancing children :-)

"It’s great to see kids dancing about again, especially during this pandemic we’re in…"
28 minutes ago
Downtown Vinnie commented on Cigar Box Blues's video
Thumbnail

- Beans fer Breakfast! - One of Daves last projects

"Very kool.Just not gonna be the same here...."
31 minutes ago
Doug Thorsvik commented on Uncle John's video
Thumbnail

Hobo’s Lullaby - repost of our recently departed friend.

"Well chosen Uncle John! I especially appreciated Dave’s comments at the end. He will be…"
33 minutes ago
Downtown Vinnie commented on Adam Cripps's video
Thumbnail

Eleanor Rigby (Beatles cover)

"A heartfelt song and performance.Thanks so much for todays inspiration.Love it."
36 minutes ago
Downtown Vinnie commented on Downtown Vinnie's video
Thumbnail

I Shall Be Released

"Thanks so much ,gang.Used to play this a long time ago when I was a twelve string balladeer..Tryin…"
38 minutes ago
Doug Thorsvik commented on Rope Walker Country Star's video
Thumbnail

Song For Dave Lynas

"A very tasteful and fitting tribute Rope! Dave’s creative contributions and interactions will…"
42 minutes ago
bemuzic posted a video

Busking, St Ives w 3 String Cigar Box Guitar - Magic Paints, with dancing children :-)

Busking, St Ives w 3 String Cigar Box Guitar - Magic Paints, with dancing children (I turn the camera round to the dancing children about a minute in)This is...
46 minutes ago
Doug Thorsvik commented on Poorness Studios's video
Thumbnail

Candida (on cigar box guitar & kazoo)

"That’s exactly what I was talking about Kale! You put a big smile on my face this morning. I…"
57 minutes ago

Music

© 2021   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->