CIGAR BOX VIOLIN by W.J. Sutherland, Science and Mechanics Magazine - 1949

(by W. J. Sutherland, published in Science and Mechanics Magazine - 1949)








By W. J. SUTHERLAND

After you've smoked the cigars, you can make music with the box they came in. It's an easy job to make a cigar box violin, so let's begin. First remove lid from cigar box (B in Fig. 4). Cut out hole 2 1/4 inches in diameter with fret saw or pen knife. Then cut a piece of broom handle, quarter it and cut in lengths the same as depth of cigar box (A in Fig. 4). Next glue quartered pieces in four corners of cigar box. This will reinforce the box and also improve the tone. Sandpaper inside of cigar box and apply two coats of shellac, allowing first coat to dry before putting on the second.

Finger board is made from a broom handle 27 1/2 inches long and 1 inch in diameter (C in Fig. 4). On one end cut out a piece 2 1/2 inches long halfway through handle. Then glue finger board (broom handle) to lid (B in Fig. 4) and secure with small woodscrew. Drill screw hole to prevent splitting. Put screw in from up through lid into handle. At other end of finger board (E in Fig. 4) drill 3/8 inch hole 1 inch from end through top to bottom. This is so string can wind on D (Fig. 4). Then make saw cut at edge of hole to set in piece of brass 1/16 inch thick, 3/4 inch wide and 3/16 inch high.

A small notch is cut in brass with edge of file to keep string centered (J in Fig. 4). The piece of brass prevents string from cutting into handle or finger board. Another hole 1/4 inch, is drilled at right angles through 3/8 inch hole already drilled. This hole is for peg (D in Fig. 4). Peg is tapered, therefore 1/4 inch hole must also be tapered. This is easily done by wrapping a piece of fine sandpaper once around peg. With a rotating motion sand 1/4 inch hole to taper of peg. Take sandpaper off peg and fit frequently. This is important. When string is strained peg is pushed into tapered hole and must hold at desired position when turned. A supporting bracket is made from a piece of wood 2 1/2 inches long, 1 1/2 inches wide, and 1/2 inch thick (F in Fig. 4) and glued to box and finger board and secured with two small nails.

You are now ready to sandpaper box and finger board. Apply two coats of shellac allowing first coat to dry. Use fine sandpaper again before second coat is applied. Tail piece is made of brass 1 1/2 inches long, 1/2 inch wide and 1/16 inch thick (G in Fig. 4). Drill hole 1/16 inch in diameter centered 3/8 inch from end. Then slot with hacksaw. Slightly bend 1/4 inch from top; this prevents string from slipping out (String should have piece of metal secured on end as anchor.) From other end of tail piece drill drill 1/8 inch hole 1/4 inch from end, and another 1/8 hole 3/4 inch higher. These holes are centered. Tail piece is fastened to end of box, 1/4 inch above surface of box (G and A in Fig. 4). Bend in tail piece should project from box.

H in Fig 5 shows the bridge, made from a piece of hardwood 5/16 inch at bottom tapered to 1/8 inch at top, 1 3/4 inches wide, and approximately 5/8 inch high.

Bridge should hold string 1/6 inch off finger board. Bridge should be half-way between resonance hole and tail piece. Bridge will remain in position when string is tightened or strained.

Bow can be made from wire coat hanger (K in Fig. 3). First straighten and form as shown in diagram. End of wire is soldered to form handle on bow as shown in M in Fig. 3. Then a spool of fine white silk thread is tied at one end of bow and stranded to other end of bow( L in Fig. 3). Thread tight enough to keep thread taut. When readt to use rub thread over a piece of rosin. If you have a regular violin bow, you can of course, use it instead of making one, Peg shown (D in Fig. 1) is a regular violin peg. You'll find that a guitar 3rd string, if you have one, gives best results. And peg rosin and string can be purchased at a music store in your neighborhood.

The cigar box violin is played by holding box between the knees with finger board resting on left shoulder; this allows free use of hands. The bow is held in right hand and drawn over string. Finger is moved up and down pressing string against finger board to get the desired notes. This violin has a range of two and a half octaves, and should be tuned to G on piano.

Views: 5879

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources


Discussion Forum

Blog Posts

Leonard Cohen Life

Posted by Keith Rearick on October 7, 2021 at 11:18am 0 Comments

CBGer’s Lament

Posted by Ghostbuttons on October 3, 2021 at 12:11am 0 Comments

Sasquatch!

Posted by Mark E. Martinsen on September 29, 2021 at 8:39pm 3 Comments

Prototyping with a big ol' wine box

Posted by Ben on September 23, 2021 at 4:00pm 0 Comments

Mr. Bells

Posted by Stephen Cohen on September 4, 2021 at 12:30pm 0 Comments

Latest Activity

Uncle John commented on ChickenboneJohn's photo
11 minutes ago
Uncle John commented on ChickenboneJohn's photo
Thumbnail

BOXSTOCK, UK Cigar Box Guitar Festival

"Great photo. I hope we still somehow hear from Mr. Belly."
12 minutes ago
Uncle John commented on ChickenboneJohn's photo
Thumbnail

BOXSTOCK UK Cigar Box Gutar Festival

"Cool. I wish I could have been there, listened and done a couple of songs."
13 minutes ago
Uncle John commented on ChickenboneJohn's photo
Thumbnail

BOXSTOCK UK Cigar Box Gutar Festival

"Great looking stand, gits and folks.  I saw on FB that Paul Smith said it was a great…"
13 minutes ago
Profile IconIan McAlpine, Jimmy and jan Pili joined Cigar Box Nation
21 minutes ago
Martin replied to Martin's discussion Drawings or pictures on the box in the group Building a Cigar Box Guitar 101
"Hi guys, I found this  and I will try it on the box. It is called a transfermarker. I…"
3 hours ago
ChickenboneJohn posted photos
4 hours ago
BUGGSY liked Richard Sundberg's video
6 hours ago
Art Box Guitars liked Randy S. Bretz's photo
7 hours ago
Art Box Guitars updated their profile
7 hours ago
the anonymous pick commented on Poorness Studios's video
Thumbnail

Big White Taxi (a tribute to Dave Lynas)

""felt i had to do something ,but couldnt quite figure out what to do " .. I'm…"
9 hours ago
Darryl Tuttle posted a status
"Anyone ever use a masuter 4040 cnc router?…thinking about getting one"
13 hours ago

Music

© 2021   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->