I'm currently building my first cigar box guitar, in fact it's pretty much finished . One of the last things I need to do is install the piezo. I've noticed that everyone seems to use a hot glue gun to mount it, but I don't have one. Is there any alternative? Can I use wood or super glue instead ?

Views: 329

Reply to This

Replies to This Discussion

Thanks. From what I've seen folks are using the hot glue to pretty much encase or insulate the piezo so it only draws sound from one source or directon. I have actually considered taping it in place just to see how it sounds. I can always glue it in later if I feel it needs to be more isolated. Hope to post some pics of it later.

  Hi Austin,

                You're right about taping it in place to find the sweet spot. Some folks put it behind the bridge on the bass string side to give it more low end when the high string is too bright. Some put it in front of the bridge on the bass side for more mids. And on the high string side if too low end. Two piezos wired in series (-  +- +) and placed on both sides can give a fuller sound too. Underbridge rod piezos are the ultimate but disc piezos have their own advantages.

      You can wrap it in electrical tape and doublestick tape or hot glue it in. Silicone caulk works good with a two day dry time.. 3M Marine sealant 5200 is a mistake I learned twice...; )

Thanks for the advice Jim. It does seem to be missing some low end when I play it acoustically, so I'll keep what you said in mind. May try it out in a few spots just to see what difference it makes. Never thought of using caulk, that's a good idea! Hope to post some pics of it later today.

When I run out of glue sticks I use RTV or Shoe Goo.,,.I use a drop of wood glue to tack the disk to the box, then add the shoe goo.,.,dries overnight.,.,.,I suspect duct tape would work.,.,wrap in leather or cardboard or thin pieces of wood and use wood glue.,.,

options.,.,.,

Actually I just put it on the inside of the lid (under the bridge on the bass side seemed to be the best sounding spot) and stuck a piece of duct tape over it. Is there any disadvantage to doing this? Because actually it sounds pretty good.  

The disadvantage is you used the last of the duct tape.,.. lol

Lol Jerry, no actually I have about half a roll left. Camo pattern Gorilla tape,  pretty tuff stuff.

For the best placement I put my bottle capped piezo unreel the through neck in bridge position I find this is the best for the sound and keeps the noise from out side sauces to a minimum I use hot glue or 5 minute Arildite incassing the piezo in a bottle cap is a great way to get the best out of the piezo some will say they don’t but I’ve been using this method for the last 25 builds never a problem with the issues raised before , hot glue guns are cheap I’d advise to buy one anyway just my 2 cents worth of info hope it helps .

Thank you,  I'm seeking all the advice I can get at this point. You encase the piezo in a metal bottlecap I take it? The piezo I have wouldn't fit inside a standard bottlecap.  When I built mine I followed Glenn Watt's advice and created about an 1/8 inch gap between the neck and the inside of the lid to allow the lid to vibrate. That's where I placed the piezo ,in that gap under the bridge more towards the bass side. Seems to sound pretty good but I'm no expert. I realize hot glue guns are cheap, but things are tight for me right now. I plan to pick one up asap.  If you saw the tools I used to build this one you would laugh. Luckily I'm pretty resourceful and had some stuff such as tuners already lying around. I have less than  $18 in this build and most of that was the box and poplar 1×2 for the neck.

great looking build are made with a small amount of instruments, sometimes not even power instruments. 

Hi, I myself would be a bit suspect of ductape maintaining a good firm contact of the disc to timber, especially over a period of time, I'd hate to have to get back in the box at a later date due to the sound deteriating.

you could use the double sided adhesive sheet used for applying pickgaurds, I do in my CBG's, you would fit dozens of discs from one sheet. 

The manufacturer of the piezos I use recommend superglue gel to get the best response from their piezo pickups.  

Taff

RSS

The Essential Pages

New to Cigar Box Nation?How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

My first real work bench.

Started by Cause the Blue rat in Other stuff - off topic, fun stuff, whatever. Last reply by Cause the Blue rat 3 hours ago. 8 Replies

Building a basic bridge?

Started by Frank Scott in Building Secrets, Tips, Advice, Discussion. Last reply by the anonymous pick 4 hours ago. 23 Replies

Tone/volume knob position

Started by Brent Kasl in Building Secrets, Tips, Advice, Discussion. Last reply by the anonymous pick 12 hours ago. 6 Replies

VIDEO: DIY Dobro Ideas... from Mailboxes to Paint Lids!

Started by Shane Speal shanespeal.com in Feature Articles. Last reply by the anonymous pick yesterday. 5 Replies

Blew it

Started by Brent Kasl in Performances, How to Play, Lessons, Concerts. Last reply by Taffy Evans on Thursday. 4 Replies

fret cutting jig

Started by Alan Dillard in Building Secrets, Tips, Advice, Discussion. Last reply by Bruce Young on Wednesday. 7 Replies

VIDEO & PHOTOS: Naughty Cigar Box Guitar Has "Peep Show" Window!

Started by Shane Speal shanespeal.com in Feature Articles. Last reply by GARAGE HERMIT on Wednesday. 2 Replies

R.L. Burnside

Started by Mike Seymore in Performances, How to Play, Lessons, Concerts. Last reply by Mike Seymore on Tuesday. 6 Replies

Blog Posts

Double cake box guitar

Posted by Hans on October 17, 2018 at 8:00am 9 Comments

fret marker ideas

Posted by Philip Hopper on October 17, 2018 at 4:06am 7 Comments

CBG project

Posted by Philip Hopper on October 13, 2018 at 3:45pm 3 Comments

Introduction

Posted by Freddie Cisneros on October 13, 2018 at 2:24pm 2 Comments

Latest Activity

Philip Hopper commented on Philip Hopper's blog post fret marker ideas
"Good morning Bob, I have decided to try something very similar using a dark wood veneer laminated…"
4 minutes ago
Hans commented on Hans's blog post Double cake box guitar
"No need to apologize, Danny, there are no stupid questions! (I teach at a college and that’s…"
2 hours ago
Gary Holdsworth commented on Gary Holdsworth's blog post New CBG build from the land down under
"Body has basic base paint on now still need to add the signage to the front back and…"
2 hours ago
Jeff 'Bones' Reilly commented on Darryl Tuttle's photo
Thumbnail

t50

"That will make a great amp ."
2 hours ago
Jeff 'Bones' Reilly liked Darryl Tuttle's photo
2 hours ago
Danny Connors commented on Hans's blog post Double cake box guitar
"Forgive me the stupid question (I'm new to this CBG thing...) This looks like a neck through…"
2 hours ago
Danny Connors commented on Hans's blog post Double cake box guitar
"Beautiful work!"
2 hours ago
Danny Connors commented on Randy S. Bretz's photo
Thumbnail

Experimenting !

"What are you trying to find out?"
2 hours ago
Danny Connors commented on David Bowes's photo
2 hours ago
Danny Connors liked David Bowes's photo
2 hours ago
Danny Connors commented on David Bowes's photo
2 hours ago
Danny Connors liked David Bowes's photo
2 hours ago

Music

Loading…

© 2018   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service