Views: 376

Reply to This

Replies to This Discussion

I decided to make a couple of ukulele necks today.  Please allow me to put in a little back story here.  I have been skeptical about how accurate my cut off saw is on the 90 degree setting.  When I cut the joint where the neck meets the cigar box body I want the cut to be a dead ass perfect 90 and also a fair amount of neck drop.  My rule of thumb is to determine how much neck drop I want, and then double it.  This may seem excessive, but it works for far.  I found that the neck drop gets cut in half or more when the strings are installed and tightened.  I blame it on the box flexing and the top dipping under the bridge.  Of course that can be corrected to some extent by bracing and adding more braces here an there under the top.  I prefer to keep the inside of the box free of extraneous wood when possible because it can dampen sound.

Back to the saw.  I made my cut and set the neck on the box and checked the angle with my trusty, rusty square.  It was off by almost 1/8" at the top.  Not acceptable.  I dialed in about a degree of more angle on the saw and cut again.  Now the neck is leaning the other way.  I decided to check my square by drawing a 90 degree line on a piece of plywood from a factory edge, then flipping the square over and drawing another line nearly on top of the first line.  This showed me that my square was off.  The lines were not exactly parallel.

I then got my speed square (1 piece) out of the van and checked that.  It was ok.  I didn't want to make any more cuts on that neck as it was already getting a little short.  So I got a piece of scrap 1 X 2 , set my saw back to 90 and made the cut.  I set the scrap on my level bench top and measured that with the speed square and also a drafting triangle.  It was dead on perfect.  Now I know my saw is good at 90 and also that I have a bad square.  That square is good enough for cutting 2 X 4s for framing, but not good enough for guitar or uke necks.

Hope my story wasn't too boring.  anyone else had similar experiences? 

Thanks for the response.  It was a good learning experience for me.  I learned how to test a square on Youtube some time ago.  In fact, you can actually adjust a framing square.  The square I was using was a Stanley with a plastic handle.  It now resides in the trash can.  However, it was well used and rusty and pretty beat up.  I now prefer the carpenter's speed square.  A one piece design made of aluminum.  The Stanley had a blade attached to the handle with 3 rivits which can loosen up over time and use.  I also learned that my Ryobi compound mitre saw is accurate, at least at 90.

Also, making a test cut on a scrap could possible prevent a disaster.

Fish it back out of the trash, break off that bit of plastic, and use the steel part for a trapeze tail piece, pick guard, string anchor, mag pup trim ring, cover plate for a wiring access/hole, bridge ground, headstock decorations, fret rocker, glue it to the side of your fret saw for a depth-set, glue some sandpaper to it for a fret leveler,

other ideas folks?

Sounds like good ideas.  I like the fret leveler best.   Thanks for the ideas.

It also helps to check to see if your straightedge is actually straight. That could play hell with your fret jobs.

Agreed.  I just use the stainless rulers.  Not perfect, but adequate for the moment.  I would like to have one of those StuMac fret rockers someday.

I have this number beaten into my head from molded plastic parts - 1 degree is 0.017" inch per every inch of length.  It adds up quick. An 1/8" off center is probably closer to just a half a degree over a neck length.  There are some good how-too's for squaring a miter saw, mine was off a bit right to left.

That is a good number to know.  The real test is when you string up your instrument.  The strings tell the story.  From the nut, down the neck, over the sound hole, to the bridge and the termination. It all has to be perfect.  Otherwise, it looks like shit.  

I'm with ya except if it is very primitive then it kind of slides by.  But also I realized I am usually the most critical of my projects whatever they may be.  I have a couple a bit off center and worry I could make them worse if I try to tweak them, so far I have left them alone, plus it helps me remember for the next one. 

Yes, and you can compensate a little by moving the bridge around, but not much.  Cutting the end of the neck on a non-neck through is about the most critical cut on a CBG.  I have tried many methods, including  Japanese pull saw with home made mitre box, band saw, etc., etc.  Finally got a decent cut off saw and then had to put a $50 blade on it (fine).  That is working well now that I have thrown out the offending square and using better squares.  

Square!?!?!?   Wowsers...  way to technical for me...

While a speed square seems to do the trick for me, I still find that if I am off the slightest bit on my cut with a hand saw, the things can be just the slightest bit out of whack.

Or maybe my head is slanted and everything I see looks crooked......


The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources


Cigar Box Amp Mods

Started by Cigar Box Nation in Feature Articles. Last reply by RTZGUITARS yesterday. 14 Replies

Blog Posts

Mr. Bells

Posted by Stephen Cohen on September 4, 2021 at 12:30pm 0 Comments

Bookie's Poor Man's Dobro

Posted by Steve Bookout on July 18, 2021 at 2:04pm 3 Comments

Get your groove on for free

Posted by François on July 13, 2021 at 3:05pm 1 Comment

Latest Activity

CLG posted photos
22 minutes ago
Doug Thorsvik posted a video

Beer Barrel Polka: 3-string (G1G2D3) Cigar Box Guitar

Cigar Box Guitar Slingers - Spokane, 73rd Zoom Mtg Sep 13, 2021. More info and free songbooks:
41 minutes ago
bemuzic commented on bemuzic's video

Busking, St Ives w 3 String Cigar Box Guitar - Magic Paints, with dancing children :-)

"thanks Brian and Doug, yep a few good minutes of connecting with people through music  and…"
42 minutes ago
Doug Thorsvik commented on bemuzic's video

Busking, St Ives w 3 String Cigar Box Guitar - Magic Paints, with dancing children :-)

"It’s always fun to see children respond to music. So unselfconscious and authentic. Thanks…"
46 minutes ago
Doug Thorsvik commented on Jim Morris's video

For Dave

"Heartfelt tribute Jim! A beautiful reminder of how Dave influenced us here at CBN."
55 minutes ago
BrianQ. commented on bemuzic's video

Busking, St Ives w 3 String Cigar Box Guitar - Magic Paints, with dancing children :-)

"It’s great to see kids dancing about again, especially during this pandemic we’re in…"
56 minutes ago
Downtown Vinnie commented on Cigar Box Blues's video

- Beans fer Breakfast! - One of Daves last projects

"Very kool.Just not gonna be the same here...."
59 minutes ago
Doug Thorsvik commented on Uncle John's video

Hobo’s Lullaby - repost of our recently departed friend.

"Well chosen Uncle John! I especially appreciated Dave’s comments at the end. He will be…"
1 hour ago
Downtown Vinnie commented on Adam Cripps's video

Eleanor Rigby (Beatles cover)

"A heartfelt song and performance.Thanks so much for todays inspiration.Love it."
1 hour ago
Downtown Vinnie commented on Downtown Vinnie's video

I Shall Be Released

"Thanks so much ,gang.Used to play this a long time ago when I was a twelve string balladeer..Tryin…"
1 hour ago
Doug Thorsvik commented on Rope Walker Country Star's video

Song For Dave Lynas

"A very tasteful and fitting tribute Rope! Dave’s creative contributions and interactions will…"
1 hour ago
bemuzic posted a video

Busking, St Ives w 3 String Cigar Box Guitar - Magic Paints, with dancing children :-)

Busking, St Ives w 3 String Cigar Box Guitar - Magic Paints, with dancing children (I turn the camera round to the dancing children about a minute in)This is...
1 hour ago


© 2021   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->