I bought some of these pickups for a project guitar. These pickups are close to the same output as the original Danelectro pickups. They don't use the same magnets. Dano used Alnico VI and then settled on Alnico V while these pickups use a ceramic magnet. Not that ceramic magnets are bad(these are good pickups), the Alnico magnets give a sparkle-bright tone to these pickups with low wind output.
I got these pickups because they have a Strat type mount, however, they don't fit in the Strat pickguard without some carving modifications. Original Dano pickups had different mounting that mounted to the back of the guitar cavity. Those would work in a CBG very well because it wouldn't add weight to the top.
One issue with these pickups is they are all wound the same direction and have the same magnetic polarity. So if you have more than one in a guitar, you'll have that out of phase sound playing both pickups that some people like and some don't. You also won't have noise free humbucking in the middle position.
Original pickups had a bar magnet with wire wrapped around it and wrapped in paper, then stuffed into the tubes. So I was interested in how these were put together. First I looked at the wire and they have 3 wires. A bare ground wire and 2 coated wires for coil start/hot(red) and a coil end wire/ground(white). That makes switching the wind direction easy, you just switch the Hot/signal(red) wire to ground and the coil end/ground(white) wire to hot/signal. That'll end the out of phase sound, but you'll still have noise/non-humbucking issue. So first I checked the polarity with my compass.
Then I took it apart.

Views: 775

Reply to This

Replies to This Discussion

These come apart easy, but you always want to go slow and easy when taking a pickup apart because the wires are delicate and easy to break. Also voids any warranty or replacement from the seller.
Flip the pickup over to see the bottom. It has wires coming out on one side and 2 nuts holding the mounting plate to the pickup. one of the wires is bare and short with a small connector on it that goes under the nut closest to the wires.

Unscrew the 2 nuts(6mm/7/32") and set aside. The short bare wire's eyelet won't pass through the hole in the plate, you have to carefully fold the ring of the eyelet to pass through. Pull the insulated wires through the hole first and then the bare wire with eyelet.

Then you gently slide the cover tube off the non-wire side first and  gently pull the coil assembly out of the other side. It will not come all the way out because of the eyelet, but far enough to do what you need to do. This coil is basically half of a dual rail humbucker for a Strat or Tele. It has a bobbin coil with the bar magnet in the middle of the bobbin like a Firebird pickup is made. The side where the magnet is flat with the bobbin is the bottom screw mount side and the side with magnet protruding out is the top.

Next, you place the coil face down on a hard surface with the protruding magnet side down. Gently push the coil bobbin downwards with as much equal force on all sides forcing the magnet to be flush with the bobbin on the bottom side and protrude out of the top.

One side of the magnet has a bit of white paint and was on the bottom, now it will be on top.

Next step is to gently turn the coil 180 degrees and push back into the tube(new bottom flat side towards the screws) while guiding the wire through the hole in that tube. Push the other side tube on. Feed the bare eyelet and insulated wire through the baseplate. Note that the baseplate has 2 ridges that face the tube and flat on bottom side. open the bent eyelet without damaging it and put on screw. Attach nuts without over torquing them.

Then recheck with Compass. It should read opposite of what it did before and recheck the coil wires to insure the coil wasn't damaged. Success, With wiring it up White hot & Red ground, this pickup will be RWRP and hum-cancelling/humbucking when played with another pickup.

 Very cool, Paul!

Thank you!

Not everyone needs to do this, but if they do need it they'll have a visual and read out to make it happen.
I plan to show how to convert a dual rail minibucker into a real Firebird soon and how to wax pot pickups too.

 I enjoyed this thread and am looking forward to both of those others. Rather timely with the wax potting especially.. Going to be winding some hotter pickups soon and will probably have to start using the wax.

 Thank you!

I have a small Crock Pot for Potpourri I plan on using to dip the pickups. Also thought about dipping the pickups in varnish like Gibson and Fender did back in the day.

Thank you for the reference Paul!!

Very nice.  I make and experiment with all kinds of pickups myself, I know this will be remembered when I come to such situations.

Your welcome and I hope it helps, just remember to go easy and slow with it as not to damage the coil wires.

A forum discussion on the pros & cons of wax vs varnish.

Wax Potting vs Lacquer Potting.... (dimarzioforum.com)

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

Doug Thorsvik posted a video

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

Cigar Box Guitar Slingers - Spokane, 195th Zoom Mtg 03/25/24. Only 1-finger chords, free songbooks here: https://www.cbgslinger.com/download CBG SOF Songbook...
13 minutes ago
A.D.EKER commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Thank you Poorness ! for loving it ! appreciated!"
16 hours ago
Southern Ray replied to Timothy Hunter's discussion just came accross this pickup idea on youtube.
" Very interesting. Thank you Timothy!"
16 hours ago
Kent Thurston updated their profile
17 hours ago
Southern Ray posted a photo

Punch Project!

She now sports gold metal CBGitty knobs, speaker and an Artec 2.5 watt speaker. Finished this in…
18 hours ago
Southern Ray posted a photo

Project Punch!

Gonna finally get back on this long-delayed project that is more than half complete. (The matching…
18 hours ago
Poorness Studios liked A.D.EKER's video
20 hours ago
BrianQ. left a comment for Rob (Uker) Porras
"Hope this helps?"
20 hours ago
Doug Thorsvik commented on Doug Thorsvik's photo
Thumbnail

Dueling Flatheads

"I appreciate the kind words Papa D! I have always loved the look of these cigar boxes. Glad to have…"
23 hours ago
A.D.EKER commented on A.D.EKER's video
yesterday
A.D.EKER posted a video

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

The recorded History By Alan Lomax for the library of Congres of the Blues, from Mc Kinley Morganfield (Aka Muddy Waters) the in this take recorded Tribute ...
yesterday
Papa D commented on Doug Thorsvik's photo
Thumbnail

Dueling Flatheads

"Beautiful..Nice work Doug.."
yesterday

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->