I just completed construction a a Gitty license plate guitar. After I added the strings and started to adjust the strings, I noticed the action was so low that the strings are hitting the frets and giving a real tinny sound. I need to raise the action some. What is the best method of raising the action?
The open space under the license plate seems to be contributing as the bridge lowers as the strings tighten.
Tags:
Some of those license plates could be a little bendy, run a brace inside, across the body.
First, do the internal bracing that BrianQ recommended. If you still more clearance you can build up your bridge with a piece of hardwood as a foundation and or change the nut.
Hi rick, also check for high frets in buzzing area. A short straight edge over three frets and if rocking is evident you found a high fret.
Taff
Taff
i know they have fancy luthier ways of handling that fret. Do you hit it with a file or is that not cool?
thanks
Hi Tim, well if you come across a high fret there are a few ways to remedy it, and it depends on what has caused the high fret.
it could have just lifted out of its slot, now filing it ain't going to fix that, it's still going to be out of its slot when you finish filing. So applying glue and holding the fret down until it sets is the way in this case.
Sometimes the fret slot may not be deep enough and holds the fret up, in this case I'd say remove the fret and rework the slot.
Sometimes it can be up due to an uneven fingerboard or lack of good levelling when first installed, then I would use a file to level the fret with the others. One then has to recrown the fret and polish.
sometimes a Factory guitar can have less than perfect fretting. These do not become evident until the customer asks for a low action, so a simple job can turn into a not so simple one. A complete fret dress.
When I get a new guitar in because of a high action I immediately think, why? Often times it's to hide the buzzing caused by clumsy fret installation.
Taff
Thank you Taff,
I see what you are saying in each case. Thank you for that knowledge, I know that comes for years of experience and I appreciate it.
tim
Madgomer,
would the sound be better If the plate were connected in a rigid way to the bracing (glue or screw)?
Or the contact between the plate and bracing have a flexible connection (rubbery glue or a rubber washer)?
Or would the bracing be ideal around the sides, leaving the plate/soundboard free to vibrate in the center, unencumbered?
or a center post mounted from inside the box to the underside of the plate?
Or some other type of approach?
thank for your thoughts
tim
Started by Justin Stanchfield. Last reply by Taffy Evans Mar 20. 9 Replies 2 Likes
Started by BrianQ.. Last reply by MadGomer Feb 27. 2 Replies 4 Likes
Started by Ian Boyd. Last reply by Ian Boyd Dec 11, 2023. 1 Reply 0 Likes
Started by Michael Myers. Last reply by Michael Myers Apr 20, 2023. 8 Replies 0 Likes
Started by Brenda. Last reply by MadGomer Dec 3, 2022. 5 Replies 0 Likes
Started by Wichita Sam. Last reply by Taffy Evans Nov 14, 2022. 21 Replies 1 Like
Started by Michael Myers. Last reply by Taffy Evans Nov 3, 2022. 4 Replies 0 Likes
Started by Robert Killen. Last reply by Paul Craig Oct 14, 2022. 23 Replies 2 Likes
Started by Larry Sobol. Last reply by Larry Sobol Oct 1, 2022. 6 Replies 2 Likes
Started by jon neet. Last reply by Taffy Evans Aug 16, 2022. 6 Replies 1 Like
Started by Doug Laffin. Last reply by Order99 Aug 11, 2022. 4 Replies 1 Like
Started by Paul Craig. Last reply by Paul Craig Jul 17, 2022. 14 Replies 1 Like
Started by Roy Smith. Last reply by the anonymous pick May 15, 2022. 2 Replies 0 Likes
Started by Al Lobe. Last reply by BrianQ. May 10, 2022. 18 Replies 0 Likes
Started by Michael Myers. Last reply by Taffy Evans May 6, 2022. 5 Replies 1 Like
Started by Michael Myers. Last reply by Michael Myers May 2, 2022. 5 Replies 0 Likes
Started by Wichita Sam. Last reply by MadGomer Feb 23, 2022. 2 Replies 4 Likes
Started by Lionhound. Last reply by MadGomer Feb 18, 2022. 8 Replies 0 Likes
Started by Paul Craig. Last reply by Paul Craig Dec 9, 2021. 18 Replies 2 Likes
Started by Ken Hope. Last reply by Christopher G Daniels Nov 29, 2021. 4 Replies 1 Like
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
May 11, 2024 from 11am to 8pm – Speakeasy Grill
0 Comments 0 Likes© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!