Looking for suggestions on how to improve the distance between the tail piece and bridge location.

Right now due to length of Box and 24.75" scale, the bridge is positioned about 3" from edge of box then the tailpiece is extended another 2" holding the three ferrules.

Views: 223

Reply to This

Replies to This Discussion

What do you mean by "improve"?

Do you want the bridge closer to the edge or closer to the center of the box?

Does the neck have a separate fret board? Is it fretted of a slider?

Is the neck notched for the box lid?

A photo could answer a lot of questions.

photo below

The yellow tape line shows bridge position

Still not clear on what the chief concern is.

Is the bridge angle so low that the guitar doesn't play correctly?

If you want a greater angle from the tailpiece to the bridge (without raising the bridge) then you could cut the top of the tailpiece down so the brass rivets sit lower relative to the bridge, thus increasing the angle. On the other hand, if it plays okay, don't worry about it. Increasing downward force is not going to drive a cigar box top much more that it is currently. So if the objective is increased volume, it may be a lot of work for little gain.

Take a look at a hard-tail bridge and you'll see that there is really no bridge angle or down force, but hey are used commonly.

Bridge to box edge about 3" then the tailpiece as shown is about 2" and due to that length it is very low angle to the bridge

Attachments:

Is your fretboard flush with the box? If so, that's the real problem.

If it helps the angle enough the easiest thing would be three new string holes close to the box

Hi Brent, as I have mentioned before a simple line drawing before one starts building will help plan bridge position, neck set and break angle. Anyway................

If more angle is needed behind the bridge I would put a device, be it wood, brass, rod or flat, fitted where the two screws are with screw caps [using those two screws] behind the bridge on the edge of the lid, and run the strings under it - or through holes - and then to the bridge. Think string trees that would normally go on a peghead for the same reason.

Taff

Hi Brent, just wondering if you had a chance to address this, if so how you fixed your problem.

Taff

Finishing up an Alec Bradley American Box first with black dyed neck, chrome tuners, pickup and bridge, and walnut fretboard, then will most likely guide the strings on the build in question under a rod or screw held in place by two eyescrews then up towards bridge as mentioned. Should work fine, thanks

Thanks Brent, your new build sounds interesting.

I 'm surprised I received an email saying you had responded with in an hour??? I usually get informed next day if at all when people post. I hope that keeps up.

Taff

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

smilingdog1 liked 3 String Blues's video
2 minutes ago
smilingdog1 liked Glenn Kaiser's video
4 minutes ago
Doug Thorsvik posted a video

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

Cigar Box Guitar Slingers - Spokane, 195th Zoom Mtg 03/25/24. Only 1-finger chords, free songbooks here: https://www.cbgslinger.com/download CBG SOF Songbook...
1 hour ago
A.D.EKER commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Thank you Poorness ! for loving it ! appreciated!"
18 hours ago
Southern Ray replied to Timothy Hunter's discussion just came accross this pickup idea on youtube.
" Very interesting. Thank you Timothy!"
18 hours ago
Kent Thurston updated their profile
19 hours ago
Southern Ray posted a photo

Punch Project!

She now sports gold metal CBGitty knobs, speaker and an Artec 2.5 watt speaker. Finished this in…
19 hours ago
Southern Ray posted a photo

Project Punch!

Gonna finally get back on this long-delayed project that is more than half complete. (The matching…
19 hours ago
Poorness Studios liked A.D.EKER's video
21 hours ago
BrianQ. left a comment for Rob (Uker) Porras
"Hope this helps?"
21 hours ago
Doug Thorsvik commented on Doug Thorsvik's photo
Thumbnail

Dueling Flatheads

"I appreciate the kind words Papa D! I have always loved the look of these cigar boxes. Glad to have…"
yesterday
A.D.EKER commented on A.D.EKER's video
yesterday

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->